User manual MARANTZ RC-2000MKII

[. . . ] ENGLISH CONTENTS ENGLISH: INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38 INTRODUCTION Thank you for purchasing the Marantz RC2000 Mk w learning remote control. We developed this remarkable component so that you can easily control an entire A/V system, with many more features than are typically offered with other learning remote controls. Conventional remote controls that are usually supplied with audio and video components are often difficult to use, and may be designed with many small buttons identically sized and positioned too close together. [. . . ] If re-writing of all of the desired direct mode functions has been completed, use the paper clip tip to press the operation mode button q, and select the "USE" mode. Now, all of the re-written names are available for use. Erasing the commands assigned to pages 1-4 of each direct button: Press and hold the "CLEAR" botton and press or button twice. At that point, if you press "OK" in the cursor keys, you will erase all four pages in that particular direct function. After clearing, the RC2000 Mk w will restore any factory programmed codes. If you do not wish to clear the pages, press any other key other than the "OK" button. Erasing the memory assigned to a particular button: First check the current function. (In this example, let us assume that it is LD. ) Press and hold the "CLEAR" button !4 and press the button that you wish to erase 2 times. The code previously learned by that button will be erased, and will then be either empty, or the original factory provided RC-5 codes will re-appear in its place. TUNER CD TAPE AUX AMP 3. POWER SOURCE ON ON/OFF CLONE MACRO OFF MODE MACRO LEARNING REMOTE CONTROL RC2000MK MACRO Press the MODE button to switch to USE. Note: The status and direct mode names of each page that are not rewritten remain without being erased. CH VOL How to clear (erase) the memorized codes (and any re-written names): The RC2000 Mk w has a high capacity RAM, which ordinarily will allow the learning of several hundred remote codes (and their associated new names, if desired). However, due to the fact that some remote codes occupy more memory space than others, it is possible that the available RAM fills up completely, and the "FULL" indicator appears in the LCD window. In this case, it will not be possible to learn any new remote codes without first deleting some or all of the previously learned remote codes and/or re-written names. There are 4 ways to erase learned remote codes from memory: 1 4 7 M 2 5 8 0 3 6 9 OSD GUIDE MUTE OK C While holding the CLEAR button depressed, press PLAY twice. The LD PLAY code is cleared and the original RC-5 code is recalled. 19 20 4. Erasing the memory assigned to each function command set: All codes and names, which were previously memorized for each of the functions (such as TV, LD, VCR, etc. ), can be erased. Press and hold the CLEAR button !4, and press the function button that you want to erase 2 times. You will see the "FNC - CLR?" (function - clear?) indication in the LCD window (see Figure 5). If you wish to go ahead and clear all of the memorized codes for that function button, press the "OK" button within the cursor keys !6. After clearing the memory contents for that function, the RC2000 Mk w will restore any factory programmed RC-5 codes for the function, if any, or will simply be empty. DSS MD TV LD DVD VCR 7 M 8 0 9 OSD GUIDE MUTE C LEARN While holding the CLEAR button depressed, POWER SOURCE ON ON/OFF CLONE MACRO OFF MODE 1 MACRO 2 3 4 MACRO LEARNING REMOTE CONTROL RC2000MK Figure 6 1 3 pressing simultaneously displays [ALLCLR?]. NOTE: The RC-5 codes as supplied from the factory cannot be erased from memory, but they can be replaced with different codes as you wish. By now, you have learned how to memorize codes from other brands of components, including changing the various function, status, and direct function names. TUNER CD TAPE AUX AMP LOW LEARN CH VOL 1 4 7 M 2 5 8 0 3 6 9 OSD GUIDE MUTE 1 OK 2 3 4 Figure 5 C While holding the CLEAR button depressed, press LD twice; [FNC-CLR?] will be displayed. If you want to cancel the memory clear operation, do not press the "OK" button, but instead simply touch any other button. When you clear all the commands associated with a function button, all of the learned direct function commands (D-1 through D-8, pages 1 through 4) are cleared as well. ¼ Before continuing on to the more advanced RC2000 Mk w programming techniques, you may wish to continue "teaching" the RC2000 Mk w remote control with any or all other commands for other components in your system. When you feel you've transferred as many different commands from other components into the RC2000 Mk w as you'd like, and possibly changed some or all of their names as well, then feel free to proceed to the next section. ¼ The all-clear operation takes about 15 seconds after the OK button is pressed. ADVANCED PROGRAMMING TECHNIQUES Macro mode: The word "macro" is used to describe a series of specific steps carried out in sequence. [. . . ] PROCESSOR 1 2 3 4 RF OPT COAX BYP select RF input select OPT input select COAX input bypasses Dolby Digital decoding Dolby Digital volume increase Dolby Digital volume decrease activates SLEEP timer select 6 channel discrete mode CD 1. MODE 1 2 3 4 5 6 CD CD FTS RNDM TRAY TIME CD changer next disc CD changer previous disc favorite track selection random (shuffle) tray open/close time display elapsed/remain/total repeat automatic music scan Disc 1 Disc 2 Disc 3 Disc 4 Disc 5 tape edit function recall track programming cancell track programming Selects UNIT No. Selects TITLE SEARCH Selects ENTER commands Tape 1 control (NO output) record pause stop commands MD control (NO output) record pause stop 5 VOL 6 VOL 7 SLEP 8 6-CH 7 REPT 8 AMS 2. CHANGER 1 1 2 3 4 5 6 7 8 CD 1 CD 2 CD 3 CD 4 CD 5 EDIT RCL CNCL UNIT DISC TR CATG MODE TITL TUNER 1. [. . . ]