User manual MARANTZ PM6005

[. . . ] • High quality audio design This unit has a high quality audio design such as minimized signal path, use of high sound quality parts, and large power circuit, which is possible only in discrete audio components. • Phono input connectors for connecting turntables This unit is provided with a phono amplifier so that you can directly connect a turntable and play records (Only the MM cartridge can be used (vpage 18). ). • Two-sets of speaker output terminals In addition to using two sets of speakers (Speakers A and Speakers B), you can connect to bi-wiring speakers with separate input terminals for high range and low range (vpage  17). The unit adopts screw terminals that can connect thick audio cables. Front panel Rear panel Remote 6 Index Contents Connections Playback Settings Tips Appendix High performance • Digital Input (Coaxial, Optical) This unit has a digital input terminal that allows input of digital audio from external devices such as televisions. [. . . ] IR receiver Remotely connecting Marantz devices You can transmit remote control signals simply by connecting a Marantz audio device to the REMOTE CONTROL IN/OUT connectors using the remote connection cable provided with the device. Set the remote control switch located on the rear panel of the connected audio component to “EXTERNAL” to use this feature. RC OUT NOTE • When the remote control signal receiving function is disabled, you can not perform operations with the remote control unit. Front panel Rear panel Remote 21 Index Contents Connections Playback Settings Tips Appendix Connecting the power cord Wait until all connections have been completed before connecting the power cord. To household power outlet (AC 230 V, 50/60 Hz) Power cord (supplied) Front panel Rear panel Remote 22 Index Contents Connections Playback Settings Tips Appendix Playback Turning the power on (vpage 24) Selecting the speakers for audio output (vpage 25) Selecting the input source (vpage 25) Adjusting the volume (vpage 25) Turning off the sound temporarily (vpage 25) Adjusting the tone (vpage 25) Playing CDs (vpage 26) Recording (vpage 27) Front panel Rear panel Remote 23 Index Contents Connections Playback Settings Tips Appendix AMP POWER X Input source select buttons Turning the power on 1 % Press X on this unit to turn the power on. Input indicator for the selected source lights. SOURCE DIRECT MUTE VOLUME df • Press AMP POWER X to turn on power from standby mode. • You can also turn on power by using either INPUT SELECTOR on this unit from standby mode. NOTE • Turn VOLUME on this unit to adjust the volume to the lowest level before turning on the power. 22Turning the power off 1 SOURCE DIRECT INPUT SELECTOR SPEAKERS A/B LOUDNESS Press AMP POWER X. The standby indicator lights in red. 2 Press X on this unit to turn the power off. All indicators turn off. X Front panel BASS TREBLE Rear panel BALANCE VOLUME Remote 24 Index Contents Connections Playback Settings Tips Appendix Selecting the speakers for audio output Adjusting the volume 1 Press SPEAKERS A/B to select the speaker system to be used for playback. The indicator of the selected speakers lights. 1 % Use VOLUME df to adjust the volume. • You can also adjust the volume by turning VOLUME on the main unit. Selecting the input source 1 % Press the input source select button to be played back. The indicator of the selected input source lights. Turning off the sound temporarily 1 % Press MUTE The mute indicator lights. . • You can also select the input source by turning INPUT SELECTOR on the main unit. • Muting can be cancelled by pressing MUTE again. Adjusting the tone 1 2 Press SOURCE DIRECT on this unit to turn off source direct mode. Turn the BASS, TREBLE and BALANCE control knobs to adjust the tone. Front panel Rear panel Remote 25 Index Contents Connections Playback Settings Tips Appendix Playing CDs This section uses playback from a CD as an example. 22Playback in source direct mode The signal does not pass through the tone adjustment circuitry (BASS, TREBLE and BALANCE), resulting in playback of a higher sound quality. 1 2 3 4 Press X on this unit to turn the power on. Press the input source select buttons to switch the input source to “CD”. The “CD” input indicator lights. 1 Press SOURCE DIRECT to turn on source direct mode. The SOURCE DIRECT indicator lights. 22Playback in LOUDNESS mode Playback the CD. Use VOLUME df to adjust the volume. When music is played at a low volume level, the effect of the bass and treble cannot be heard easily. The LOUDNESS function corrects the low range and high range tones in these situations, allowing you to enjoy natural-sounding playback. 1 Press LOUDNESS to turn on LOUDNESS mode. The LOUDNESS indicator lights. Front panel Rear panel Remote 26 Index Contents Connections Playback Settings Tips Appendix Recording 1 2 3 Press X on this unit to turn the power on. Press the input source select buttons to switch to the input source from which you want to record. The indicator of the selected input source lights. Recording starts. • For information on operations, see the owner’s manual of the recording device. Front panel Rear panel Remote 27 Index Contents Connections Playback Settings Tips Appendix Settings Setting the Auto Standby mode (vpage 29) Setting the remote signal receiving function of the remote control unit (vpage 30) Setting remote control codes (vpage 31) Front panel Rear panel Remote 28 Index Contents Connections Playback Settings Tips Appendix Setting the Auto Standby mode You can set the unit to automatically switch to standby mode if the unit is not operated for 30 minutes when there is no audio input. Auto Standby mode is set to on by default. Turning Auto Standby mode off 1 Press and hold SOURCE DIRECT for more than 5 seconds to turn the Auto Standby mode off. The power indicator flashes once. Turning Auto Standby mode on SOURCE DIRECT Standby indicator 1 Press and hold SOURCE DIRECT for more than 5 seconds to turn the auto standby mode on. The standby indicator flashes three times. Front panel Rear panel Remote 29 Index Contents Connections Playback Settings Tips Appendix Setting the remote signal receiving function of the remote control unit When you connect a IR receiver (sold separately) to the REMOTE CONTROL IN connector of this unit, use the following procedure to disable the remote signal receiving function of this unit. When the function is enabled, you can not perform operations with the remote control unit. By default, this function is enabled. Disabling the remote signal receiving function of the remote control unit 1 While the remote signal receiving function of this unit is enabled, press and hold SPEAKERS B for about 5 seconds. The mute indicator flashes once, and the remote signal receiving function is disabled. SPEAKERS A SPEAKERS B Enabling the remote signal receiving function of the remote control unit 1 While the remote signal receiving function of this unit is disabled, press and hold SPEAKERS A for about 5 seconds. The mute indicator flashes three times, and the remote signal receiving function is enabled. Front panel Rear panel Remote 30 Index Contents Connections Playback Settings Tips Appendix Setting remote control codes When three of these units are used in the same location, each unit can be controlled independently by setting separate remote control codes. Be sure to check the operation of each unit after setting the remote control codes. The default setting is “AMP1”. Setting remote control codes for the remote control 22To set the remote control codes to AMP2 REMOTE MODE CD 1 1 ENTER 1–3 Press and hold REMOTE MODE CD and number button 2 for 5 seconds or longer. 22To set the remote control codes to AMP3 Press and hold REMOTE MODE CD and number button 3 for 5 seconds or longer. NOTE • To restore the remote control code default setting, press and hold REMOTE MODE CD and number button 1 for 5 seconds or longer. • The remote control codes returns to the default settings when the batteries are removed. Set the remote control codes again after replacing the batteries. Front panel Rear panel Remote 31 Index Contents Connections Playback Settings Tips Appendix Setting remote control codes for this unit 1 Hold down REMOTE MODE CD and press ENTER. When remote control codes are set, the following input indicators on this unit are displayed according to the set remote control code. Remote control codes AMP 1 AMP 2 AMP 3 Input indicator CD indicator flashes three times NETWORK indicator flashes three times RECORDER indicator flashes three times Front panel Rear panel Remote 32 Index Contents Connections Playback Settings Tips Appendix Tips Contents 22Tips. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) I want to play back high quality television sound. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) I want to adjust the tone myself. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) I want sound playback that is faithful to the original sound. . . . . . . . . . . . . . (34) I want to hear music that is close to the original sound quality at low volume. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) I want to operate a Marantz CD player or network audio player using the remote control from of unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) I want to use more than one unit in one location. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (34) 22Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (35) Power does not turn on / Power is turned off. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (35) Operations cannot be performed through the remote control unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (37) No sound comes out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (38) Desired sound does not come out. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (39) Sound is interrupted or noise occurs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . (39) Front panel Rear panel Remote 33 Index Contents Connections Playback Settings Tips Appendix Tips I want to play back high quality television sound • Connect the digital audio output connector of the TV to the digital audio input connector (COAXIAL or OPTICAL) of this unit, and switch the input source to the connected (COAXIAL or OPTICAL) connector (vpage 20, 25). • This unit can play back 2 channel linear PCM digital audio signals. I want to adjust the tone myself • Use the BASS, TREBLE and BALANCE knobs to adjust the sound as desired (vpage 25). I want sound playback that is faithful to the original sound • Set the Source Direct mode on (vpage 25). I want to hear music that is close to the original sound quality at low volume • Turn the LOUDNESS mode on (vpage 26). I want to operate a Marantz CD player or network audio player using the remote control of this unit • Switch the remote control operating mode (vpage 12, 13). • Also refer to the CD player or network audio player instruction manuals. I want to use more than one unit in one location • Set individual remote control codes for each combination of devices and remote control (vpage 31, 32). Front panel Rear panel Remote 34 Index Contents Connections Playback Settings Tips Appendix Troubleshooting If a problem occurs, first check the following: 1. If this unit does not operate properly, check the items listed in the table below. In that case, disconnect the power immediately and contact your retail outlet. 22Power does not turn on / Power is turned off Symptom Power does not turn on. Cause / Solution • Check whether the power plug is correctly inserted into the power outlet. The Auto Standby mode switches the unit to standby mode when the unit is not operated for approximately 30 minutes. [. . . ] Cause / Solution Page – – – 18 – 18 – Front panel Rear panel Remote 39 Index Contents Connections Playback Settings Tips Appendix Appendix Playback on devices that have digital audio terminals 22Supported audio formats 2-channel Linear PCM Sampling frequency Bit length 16/24 bit Explanation terms P Protection circuit This is a function to prevent damage to devices within the power supply when an abnormality such as an overload, excess voltage occurs or over temperature for any reason. If a malfunction occurs in this unit, the power indicator blinks red and the unit switches to standby mode. S Sampling frequency Sampling involves taking a reading of a sound wave (analog signal) at regular intervals and expressing the height of the wave at each reading in digitized format (producing a digital signal). The number of readings taken in one second is called the “sampling frequency”. [. . . ]