User manual MARANTZ NR 1602

[. . . ] Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped. Batteries shall not be exposed to excessive heat such as sunshine, fire or the like. IMPORTANT SAFETY INSTRUCTIONS CAUTION: To completely disconnect this product from the mains, disconnect the plug from the wall socket outlet. The mains plug is used to completely interrupt the power supply to the unit and must be within easy access by the user. [. . . ] Next, disconnect the connection cables to other system units before moving the unit. € About care • Wipe the cabinet and control panel clean with a soft cloth. € Benzene, paint thinner or other organic solvents as well as insecticide may cause material changes and discoloration if brought into contact with the unit, and should therefore not be used. Playback Accessories Check that the following parts are supplied with the product. NnIllustrations Note that the illustrations in this manual is for explanation purposes and may differ from the actual unit. 1 e r nnAbout the CD-ROM (Getting Started / Owner’s manual) You need to have Adobe Reader® installed on your computer to view the owner’s manuals on the CD-ROM. Click the Adobe Reader® banner in the CD-ROM menu to install the Adobe Reader® (for Windows). Y u i 1 ENGLISH Deutsch Français Italiano Español NEDERLANDS SVENSKA РУССКИЙ POLSKI TÜRKÇE Preparing the Setup Wizard This section describes how to prepare the Setup Wizard before use. NnDo not plug the power plug of the main unit into the wall socket until these preparations are complete. What you need for this step Speaker (sold separately) Speaker cable (sold separately) 1 Place and layout speakers Connect the speaker cables to the main unit using the Setup Wizard. Before installing the speakers, connect the speaker cables to the speakers. For details on how to connect the speaker cables, see the speaker instruction manual. 1-channel (Surround back speaker) installed • Prepare enough for the number of speakers you will use. 1-channel installed SL SR SBR FL FL SW C z1 z3 FR SW C z1 FR Subwoofer (with built-in amplifier) (sold separately) Audio cable (sold separately) z2 z2 SL SR SL SR TV (sold separately) HDMI cable (sold separately) SBL Listening position SBR Listening position z1 22˚ – 30˚ z1 22˚ – 30˚ z2 90˚ – 110˚ z3 135˚ – 150˚ z2 120˚ Remote control unit / R03/AAA batteries (supplied) Setup microphone (supplied) Power cord (supplied) FL FR C SW SL SR SBL SBR Front speaker (L) Front speaker (R) Center speaker Subwoofer Surround speaker (L) Surround speaker (R) Surround back speaker (L) Surround back speaker (R) • Install the surround speakers in a position 60 to 90 cm higher than ear level. surround speaker 60 – 90 cm Front speaker Surround back speaker (When 7. 1-channel installed) • Point slightly downwards GViewed from the sideH 2 TÜRKÇE POLSKI РУССКИЙ SVENSKA NEDERLANDS Español Italiano Français Deutsch ENGLISH 2 C  onnect this unit to the television using an HDMI cable (sold separately) 3 T urn the television power on, and switch the video input to this unit (HDMI input) Preparation NOTE If this unit is connected using cables other than the HDMI cable, the Setup Wizard will not be displayed. For details on how to operate the television, see the television instruction manual. Setup Wizard HDMI IN (ARC) q Power on w Switch the input to this unit (HDMI input) 4 Insert the provided batteries into the remote control unit  q Remove the rear lid in the direction of the arrow and remove it. Playback w Load the two batteries properly as indicated by the marks in the battery compartment. VStart Setup Wizard on next page 3 ENGLISH Deutsch Français Italiano Español NEDERLANDS SVENSKA РУССКИЙ POLSKI TÜRKÇE Setup Wizard When preparations are complete, start the Setup Wizard. Use the Setup Wizard to perform connections and settings as shown in the following steps. Perform the operations as described in the instructions on the screen. [. . . ] € Input sources that are not going to be used can be set ahead of time. € To turn off the source selection menu without selecting an input source, press 3 again. € When 3 is pressed, the AMP-operation mode starts automatically (vm page 106). 7 ENGLISH DEUTSCH Deutsch FRANÇAIS Français ITALIANO Italiano ESPAÑOL Español NEDERLANDS SVENSKA РУССКИЙ POLSKI TÜRKÇE Adjusting the master volume Use VOLUME +, – to adjust the volume. [. . . ]