User manual MARANTZ MT8600

[. . . ] Model MOUNT MT8600 User Guide VP8600 Projector Mount This product is exclusively designed for the Marantz VP8600 DLP projector. SAFETY INSTRUCTIONS READ BEFORE INSTALLING EQUIPMENT 1. Always follow the instructions set forth in this manual when installing the projector using this bracket. Improper or inadequate installation could cause the projector to fall and injure someone. 9. Never hang from the projector or the ceiling bracket. Hanging from the projector or the ceiling bracket could cause the projector or the ceiling bracket to fall and injure someone. 2. The installation must be secure enough to bear the weight of the projector, the ceiling bracket, and other hardware indefinitely, and must also be secure enough to withstand vibration. Inadequate installation could cause the projector to fall and injure someone. 10. Do not install the projector in a location near an air conditioning vent or in a location subject to vibration. Such conditions could have an adverse effect on the projector and could even cause a fire or electric shock. 3. To ensure safety, all bolts and screws must be tightened securely. Loose bolts and screws could cause the projector to fall and injure someone. 11. [. . . ] Read instructions - All the safety and operating instructions should be read before the product is operated. Retain instructions - The safety and operating instructions should be retained for future reference. Heed warnings - All warnings on the product and in the operating instructions should be adhered to. Follow instructions - All installation instructions should be followed. Use only the parts provided with the mount, along with any parts (commercially available) that are specified in this manual. Make sure not to block any ventilation openings when installing the projector. Special techniques and experience are required when installing the projector with this mount. Once the projector is installed, safety checks should be conducted on a regular basis. MT8600 INSTALLATION INSTRUCTIONS PROJECTOR MOUNT Step 1 Base Plate Connectors #1 and Projector Mount Ceiling Plate 1 with ceiling mounting holes #2. Figure 1 1 4 Ceiling Wire Access 4 14" 2 3 2 8 5/8" 3 2 Plate 1 Insert Base Plate connectors #1 into the lateral positioning slots #3 as shown in #4 from the underside of Plate 1. The lateral positioning slots will give you 2 1/4" inches of lateral adjustment for projector alignment. Base Plate Connectors #1 Projector Mount Ceiling Plate 1 The ceiling should be capable of supporting a weight of at least five (5) times the projector(s) weight. Proper installation procedure by qualified personnel as outlined in the installation instructions must be adhered to. Failure to do so could result in serious personal injury. Warning Step 2 Horizontal Adjustment Plate 2 (Base Plate Connector Holes #3). Figure 2 3 Wire Access 3 10 5/8" Hardware List 1. Four (4) 3/8 (inch) nuts Fourteen (14) 3/8 (inch) flat washers Four (4) 8 (mm) screws Twelve (12) 1/4" screws Two (2) 1" rubber washers Two (2) 1" flat washers 7. One (1) Ceiling Mount #1 Two (2) Base Plate Connectors One (1) Horizontal Tilt Plate #2 One (1) Horizontal Tilt Plate #3 One (1) Projector Plate #4 3 3 Adjustment Ranges and Load Allowances Horizontal Tilt (yaw) Vertical Tilt (tilt) Rotation Lateral Shift Maximum Load Allowance +/+/+/+/10 degrees 20 degrees 15 degrees 21/4 inches 32 Lbs. 7 5/8" Plate 2 Base plate connector holes #3 provide 15 degrees of horizontal rotation adjustment. Attach horizontal adjustment Plate 2 to projector mount ceiling Plate 1 using the four (4) 3/8" (inch) nuts and washers provided. MOUNT MT8600 PROJECTOR MOUNT INSTALLATION INSTRUCTIONS continued Step 2 B Horizontal Adjustment Plate 2 (Figure 2) attached to Projector Mount Ceiling Plate 1. [. . . ] screws provided. continued over MOUNT MT8600 PROJECTOR MOUNT Step 4 B Projector Mounting Plate 4 (continued) Figure 7 CEILING Mount Side INSTALLATION INSTRUCTIONS continued Projector Mounting Plate 4 connected to Mounting Plate 3 Figure 8 Mounts Fully Assembled Ceiling Side 200 Tilt 200 Tilt Projector Side Projector Side Plate 4 Work in a group of 2 or more to carry the projector and follow manufacturer's guidelines for relocating as stated in the VP8600 owner's manual. screws previously installed in the metal studs of the plate on the ceiling (see arrow in Figure 7). screws and washers into the side of the projector Mounting Plate 4. Sequence of Assembly of Projector Mounting Plates Plate 1 Step 2 Plate 2 Step 3 Plate 3 Step 4 Plate 4 Assembly Drawing 10. 22" (259. 7) 7. 33" (186. 3) 4. 06" (103. 0) 6. 34" (161. 00) 8. 6" (218. 4) 8. 43" (214. 00) 3. 64" (92. 5) 17. 13" (435. 0) 14" (355. 6) Yaw +/- 10 degree Unit: inch (mm) +/- 20degree Tilt Lateral Shift +/- 2. 25" (57. 2) Rotation +/- 15 degree Ceiling Plate Templates 14. 0" (355. 6) 0. 87" (22. 0) 1. 3" (33. 0) 5. 5" (139. 5) 0. 3" (7. 7) 5. 5" (139. 5) 8. 6" (218. 4) 3. 8" (96. 5) CEILING SIDE 3. 8" (96. 5) 7. 25" (184. 2) 2. 75" (69. 9) Unit: inch (mm) You can find your nearest Marantz authorized dealer on our website at: www. marantz. com 1100 Maplewood Drive Itasca, IL 60143 Phone: 630 741-0300 Fax: 630 741-0301 Printed in Canada 2005 [. . . ]