User manual MARANTZ BD5004

[. . . ] BD5004 ENGLISH FRANÇAIS ESPAÑOL Laser Safety CAUTION: VISIBLE AND INVISIBLE LASER RADIATION WHEN OPEN. CAUTION: USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. THIS PRODUCT SHOULD NOT BE ADJUSTED OR REPAIRED BY ANYONE EXCEPT PROPERLY QUALIFIED SERVICE PERSONNEL. The serial number of this product may be found on the back of the unit. You should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. [. . . ] 4) Press [AUDIO] to exit. 24 ENGLISH ENGLISH Playback Playback Selecting Subtitle Language BD-V DVD-V VCHD DivX® BD, DVD-Video, AVCHD and DivX® may have subtitles in 1 or more languages. You can switch subtitle languages anytime during playback. [ / / / ] [ENTER] [RETURN] Video / audio outputs for each mode "Normal" : Normal playback mode (pure direct mode is off). "VideoOff" "Disp. Off" "All Off" : Video signal will not be output. : Video signal will not be output and circuitry for front panel display and indicators will be shut down. Introduction Connections Playback Function Setup Others BD-V 1) During playback, press [SUBTITLE]. 2) Use [ / ] to select "Primary Subtitle", "Secondary Subtitle" or "Subtitle Style", then press [ENTER]. Primary Subtitle Secondary Subtitle Subtitle Style 2 ENG/11 2 ENG/11 2/25 [PURE DIRECT] [MODE] Virtual Surround BD-V DVD-V DVD-VR MP3 WMA CD AVCHD DivX® Note · If you turn off the unit or put this unit to standby mode, the pure direct mode will go back to "Normal". · [PURE DIRECT] is not available when the setup menu is displayed. "Primary Subtitle": Sets the subtitle for the main picture. "Secondary Subtitle": Sets the subtitle for the sub-picture. 4) Press [SUBTITLE] to exit. You can enjoy stereo phonic virtual space through your existing 2-channel stereo system. 1) During playback, press [MODE] repeatedly until the virtual surround setting appears. Setting the BD Audio Mode Off BD-V BD audio mode is to choose between two ways; you could output the secondary and interactive audio accompanied by the primary audio or you could output the primary audio only. Depending on the setting of the mode, Dolby Digital, DTS, Dolby Digital Plus, Dolby TrueHD, or DTS-HD output changes between Multi PCM and bitstream. 2) Use [ / ] to select desired setting. DVD-V AVCHD DivX® 1) During playback, press [SUBTITLE]. 2) Use [ / ] to select your desired subtitle. 1 ENG /3 2) Use [ / ] to select "1" (Natural effect), "2" (Emphasized effect) or "Off". 3) Press [RETURN] to exit. Note · Select virtual surround "Off" or lower the volume if the sound is distorted. · This function cannot be used during dialog speed (refer to page 19). · For the virtual surround, audio signal will always be 2-channel PCM. 3) Press [SUBTITLE] to exit. Note · Some discs will only allow you to change the subtitle from the disc menu. · If 4-digit language code appears in the subtitle menu, refer to "Language Code" on page 48. · If the disc has no subtitle language or subtitle style, "Not Available" will be displayed. · For DivX®, the screen only displays the number of subtitle languages. "Mix Audio Output" If it is available, BD-Video's secondary and interactive audio will be output with the primary audio. · The secondary audio is the audio for the sub picture (Director's comment etc. ) and the interactive audio is the audio for the interactive application (Button click sounds etc. ). Pure Direct Mode BD-V DVD-V DVD-VR MP3 WMA CD AVCHD DivX® "HD Audio Output" Only the primary audio will be output. Set this mode in order to output Dolby Digital, Dolby Digital Plus, Dolby TrueHD, DTS or DTS-HD sound of BD through HDMI connection. · You can also set "BD Audio Mode" from the setup menu. Refer to page 33. Use this function to shut down unused circuitry to achieve high quality analog sound. [. . . ] (Check the status of the HDMI related 12 indications. ) - Check the RCA audio/video cable connections. 12, 15 25 - Check if the pure direct mode is set to "VideoOff" or "All Off". If it is the case, set it to "Disp. Off" or "Normal". - Check whether the connected display device or other device 14 supports HDCP. [. . . ]