User manual MAPPY MINI 300ND QUICK GUIDE

[. . . ] Please ask your local authority for the location of your nearest waste disposal site. The sole purpose of this manual is to provide information; it is subject to amendment without prior notification. Graupner accepts no responsibility or liability for errors or inaccuracies which may occur in the information section of this manual. We all want you to have many hours of pleasure in our mutual hobby of modelling, and safety is an important aspect of this. [. . . ] If the telemetry function of the receiver is used, the motor control must be switched to channel 6 using the optional Smart Box (see page 117 channel mapping) in order to connect the telemetry sensors on channel 5. All menus which are relevant to model helicopters are marked with a “helicopter” symbol in the “Program descriptions”: This means that you can easily skip irrelevant menus when programming a model helicopter. Installation notes The servos will be connected to the receiver outputs in the order shown on this page: Outputs not required are simply left vacant. Receiver assignment for model helicopters … … with flybarless system free or throttle (Channel Mapping with optional Smart-Box) Telemetry sensor or throttle Tail rotor servo (Gyro system) Pitch servo Roll servo Pitch- or Roll-2 servo Channel 5 Motor Model helicopters 103 Base settings Basic model-specific settings for fixed-wing model aircraft Before you start programming specific parameters, some basic settings must be entered. Down right rudder left rudder left aileron full throttle right aileron left rudder Buzzer transmitter buzzers 1x LED Description orange LED on Country setting Universal/Europe County setting France “MODE 2” (Throttle at left stick) full throttle right rudder elev. Down right aileron left aileron transmitter buz- orange LED zers 2 times flashes The country setting is described in detail below. Transmitter buz- orange LED on »MODE 1« zers 3 times transmitter buz- orange LED on »MODE 2« zers 4 times transmitter buz- orange LED on »MODE 3« zers 5 times transmitter buz- orange LED on »MODE 4« zers 6 times To choose a mode, hold the BIND-button pressed for approx. When you release the button, the transmitter should emit an audible signal and the buzzer sound stops. Later, to check the stick mode which is programmed, watch out for the Status-LED on the transmitter. Down right aileron left aileron Motor Vollgas right rudder left aileron left rudder full throttle right aileron left rudder elev. Down right rudder If you wish to use the RC system in France, the country setting on the transmitter must be set to “France” mode, as described. Two jumpers connect the two left „AILE“ and two right „DELTA“ pins. Elevator correct, rudder wrong direction Delta, Flying wing Elevator and Ail wrong direction Elevator correct, Ail wrong direction Ail correct, Elevator wrong direction Program description: base settings - fixed-wing model 105 Receiver output For maximum flexibility in terms of receiver socket assignment, the optional Smart-Box provides the means to swap over the servo outputs 1 to max. 6 - „channel mapping“; see also chapter „telemetry“ on page 113. With the Channel mapping function of the Smart-Box the six control functions of the mx-10 HoTT transmitter can be shared out between several receivers if necessary, or alternatively several receiver outputs can be assigned to the same control function; for example, you may wish to be able to operate each aileron with two servos, or to control an oversized rudder using two coupled servos instead of a single one. Rx bind Graupner HoTT receivers have to be “instructed” to communicate exclusively with a particular model (i. This process is known as “binding”, and is only necessary once for each new combination of receiver and model. Important note: When carrying out the binding procedure, please ensure that the transmitter aerial is always an adequate distance from the receiver aerials: keeping the aerials about 1 m apart is safe in this respect. Otherwise you risk a failed connection to the downlink channel, and consequent malfunctions. €Binding” multiple receivers to one model If necessary, it is possible to bind more than one receiver to a single model. This is accomplished by initially binding the receivers individually, as described in the next section. When operating the system, please note that only the receiver which was bound last will establish a telemetry link to the transmitter. [. . . ] The flexible Smart-Box includes an integral buzzer for generating audible signals and warnings for even greater flexibility and practicality. The installation set supplied makes it easy to mount the unit on the support bars of hand-held transmitters, allowing you to position it in such a way that you can read off telemetry data in real time while you control your model. The user-update facility ensures that the SMART-BOX is always up-todate, and provides a route for expanded functions in future. € Transmitter voltage display with • Country setting user-variable warning threshold • Range check • Signal quality • Receiver temperature • Receiver voltage • Servo reverse • Servo neutral position • Servo travel • Cycle time • Channel swap • Fail-Safe settings • Mixer settings • Servo test Dimensions: approx. [. . . ]