User manual MAMIYA UNIVERSAL

[. . . ] Contents Special Pointers for Using Mamiya Universal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Main Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Description of Parts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] In this case, the actual picture area covers a slightly wider field. With the 75mm lens: Use the brilliant frame for 3¼ x 4 ¼ format in the optical viewfinder for 75mm lens. With the 127mm lens: By observing the camera viewfinder, determine the field of view by using the 6 x 7 format brilliant frame for 100 mm lens as a guide. With the 150mm lens: With the 50mm lens: Attach the optical viewfinder for 50 mm lens on the accessory shoe and observe the viewfinder entire area. Determine the field of view by covering the viewfinder mask for 3 ¼ x 4 ¼ format on the camera finder window, With the 250mm lens: Determine the field of view by inserting the mask for 250mm lens in the finder mask for 150mm lens. 14 Depth of Field Scale and Infrared Photography 15 Shutter Operation Press Focus Operation Cock the shutter by moving the shutter cocking lever (19). Screw the end of the cable release which extends from the hand grip into the cable release socket (25). To release the shutter, press the shutter release trigger of the hand grip with the left forefinger. Also, the shutter can be released by tripping the shutter release lever (23). When focusing through the ground glass, keep the shutter open by the following method. Cock the shutter, regardless of the shutter speed setting. By pushing the press focus lever back to its original position, the shutter will close. There is no need to reset the shutter. PRECAUTION : Be sure to operate the press focus lever AFTER cocking the shutter. While the shutter is kept opened, the shutter cannot be released with the shutter release button. Applying an excessive force to the release button may cause shutter damage. When the press focus lever is not used, be sure to engage the lock button to prevent inadvertently moving the lever. 2. Disengage the lock button by thoroughly pushing it to the camera body side and turn the press focus lever in the shutter cock direction; then the shutter will remain open. 16 Using Flash Flash Synchronizing Table 17 Acceptable Photosensitive Material and Actual Picture Size Photosensitive Type of holder Type Nominal size 120 6 X 9 cm roll film bolder Roll film 220 120 6 X 7 cm roll film holder Roll film 220 r, 2 `XX 2 Xin. 56 X 84mm Roll film holder model K (6 X 9, 6 X 6, 6 X 4. 5cm) Roll film 120 2 b$`, , X 2 xin. 56 X 56mm 1xX 2'~in. 41. 5X56nn Plate Cut film/plate holder (type J) Cut film Cut film Plate Cut film/plate holder (type A) Cut film Polaroid Land pack film holder Polaroid film pack series 100 or 660 2 XX 3 Xin. (8. 3X10. 8cm) 2%X 3I/in52X79mm 2 XX 3 Kin. 73X95mm ; 8 2%X 3xin. 6. 5X 2%X3%in. 6. 5X9cm 4 XX 6 %in. size divided into 4 equal parts 2 XX 3 xin. 6. 5X 9 cm 9cm ' 2 K X 3 xin. 56X84mm Number of exposures 8 19 19 Roll Film Holder (6 x 9, 6 x 7) R-14 R-15 I R-10 I R-12 R-11 R-10 R-9 20 Prior to Loading Roll Film Set the automatic film wind stop device for the film to be used (120 or 220). Turn the counter change-over knob (R-4) either to the right or left until the figure appearing in the film indicator window (R-5) corresponds to that of the film to be used (120 or 220). Open the back cover By pulling out the back cover latch while pressing the back cover to the holder, the back cover can be opened. Make sure that the correct side of the pressure plate corresponds to the film used. The figure "120" or "220" is indicated on the window of the pressure plate. Reverse the pressure plate if it does not match the film Removing the Pressure Plate: Remove the plate by pushing its right side to the left, pulling it out from the plate catch (R-15). R-4 R-3 Reattaching the plate : While aligning the upper and lower edges of the plate with the flange, insert the groove into the plate catch (R-13) on the left, then hook the plate catch (R-15) on the right while pushing it slightly to the left Always ascertain that the correct side of the pressure plate corresponds to the film used. Use the convenient film sensitivity reminder dial (R-3) as a memo of film speed in the holder, turning the dial corresponding to the loaded film speed to the red mark. Loading Roll Film Avoid direct sunlight while loading or unloading film. [. . . ] Magnification indicates the ratio of image and the subject size 33 Close-up Photographing Table for 75 mm f/5. 6 Lens Close-up Photographing Table for 127 mm f/4. 7 Lens Life-size Photocopying Set The life-size photocopying set is used for actual size photography by using the 75 mm f/5 6 or 100 mm f/3 5 lens and the spacers. . A sheet for determining the position of subject to be copied and a nonglare glass which prevents reflection are included. When using the 75 mm f/5. 6 lens: When using the 100 mm f/3. 5 lens: Nonglare glass Extension legs Use spacer No. Install only the four long legs to the photocopying stand. Use spacers No. Install long legs and extension legs on the photocopying stand. 36 Tetraphoto Adapter Polaroid Land film pack 100 or 660 series is used for the tetraphoto adapter, whereby quadruple photos can be obtained by a single exposure. [. . . ]