User manual MAKITA SP6000K

[. . . ] ENGLISH INSTRUCTION MANUAL Plunge Cut Circular Saw SP6000 007654 DOUBLE INSULATION WARNING: For your personal safety, READ and UNDERSTAND before using. cutting depth No load speed (min-1) Overall length Net weight Safety class · Note: Specifications may differ from country to country. END201-2 SP6000 165 mm 56 mm 40 mm 38 mm 2, 000 - 5, 200 341 mm 4. 1 kg /II at 45° at 48° · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Symbols The following show the symbols used for the equipment. The typical weighted root mean square acceleration value is not more than 2. 5 m/s2. These values have been obtained according to EN60745. ENH101-7 EC-DECLARATION OF CONFORMITY Only for EU countries Do not dispose of electric equipment together with household waste material! [. . . ] Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and kickback. Use extra caution when making a "plunge cut" into existing walls or other blind areas. NEVER place your hand, leg or any part of your body under the tool base or 5 12. 13. 14. 15. Never force the saw. Wear a dust mask and hearing protection when use the tool. SAVE THESE INSTRUCTIONS. WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. FUNCTIONAL DESCRIPTION 000147 · Fig. 2 CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Adjusting depth of cut 2 1 1. Blade lower limit stopper 007656 000150 17. Never attempt to saw with the circular saw held upside down in a vise. This is extremely dangerous and can lead to serious accidents. CAUTION: After adjusting the depth of cut, always tighten the clamping screw securely. Loosen the clamping screw on the depth guide and move the blade lower limit stopper to the desired depth on the scale plate. For cleaner, safer cuts, set cut depth so that no more than one blade tooth projects below workpiece. Using proper cut depth helps to reduce potential for dangerous KICKBACKS which can cause personal injury. · 000029 NOTE: · Setting the blade lower limit stopper to the desired depth on the scale plate allows rough depth of cut. For accurate depth of cut, measure the actual protrusion of saw blade below the tool base. Some material contains chemicals which may 6 18. Quick stop button for 2 to 3 mm depth of cut when using guide rail (accessory) 1 Tilting to the right 1. Quick stop button 1 007659 007669 This tool has the quick stop button for 2 to 3 mm depth of cut on the gear housing aside the rear handle when using guide rail. Make a pass of the 2 to 3 mm first cut and then make another pass of usual cut. To obtain the 2 to 3 mm depth of cut, push in the stop button toward the saw blade. To release the depth of cut from this position for free depth of cut, just pull the button back. 1 Turn the positive stopper so that the arrow on it points one of two positions (vertical for 22. 5°, horizontal for 45°). Then, tilt the tool base until it stops and secure the base with the clamping screws. To get 48° bevel angle, move the lever to 48° marking as far as it will go. Turn the positive stopper so that the arrow on it points to the horizontal position. Then, tilt the tool base until it stops and secure the base with the clamping screws. 1 1. Quick stop button 007660 007670 Tilting to the left Bevel cutting 1. [. . . ] Use eye protection to help avoid injury. · When bevel cutting with the guide rail, slide the slide lever on the tool base so that the tool does not fall down on its side. 1 1. Slide lever 007666 Move the slide lever on the tool base in the direction of arrow so that it engages the undercut groove in the guide rail. Rip fence (guide rule) (Accessory) 1. Rip fence (Guide rule) 1 007675 007674 When using with guide rail (accessory) 1. Adjusting screws The handy rip fence allows you to do extra-accurate straight cuts. [. . . ]