User manual MAKITA MT360

[. . . ] A moment of inattention while operating power tools may result in serious personal injury. Safety equipment such as dust mask, non-skid safety shoes, hard hat, or hearing protection used for appropriate conditions will reduce personal injuries. Carrying 7. Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Unmodified plugs and matching outlets will reduce risk of electric shock. [. . . ] Always lead the power supply cord away from the tool towards the rear. Do not smear the tool base carelessly with thinner, gasoline, oil or the like. Draw attention to the need to use cutters of the correct shank diameter and which are suitable for the speed of the tool. 2. 9. 3 SAVE THESE INSTRUCTIONS 4 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 004925 Adjusting the depth of cut Place the tool on a flat surface. Loosen the lock lever and lower the tool body until the bit just touches the flat surface. While pressing the fast-feed button, move the stopper pole up or down until the desired depth of cut is obtained. Minute depth adjustments can be obtained by turning the stopper pole (1. 5 mm per turn). 1 2 3 4 6 5 1. Nylon nut Stopper pole Fast-feed button Adjusting hex bolt Stopper Lock lever · CAUTION: The depth of cut should not be more than 20 mm at a pass when cutting grooves. For extra-deep grooving operations, make two or three passes with progres-sively deeper bit settings. Nylon nut For tool without the knob The upper limit of the tool body can be adjusted by turning the nylon nut. The bit will protrude dangerously. 005111 1 For tool with the knob By turning the knob, the upper limit of the tool body can be adjusted. When the tip of the bit is retracted more than required in relation to the base plate surface, turn the knob to lower the upper limit. Knob 004926 Stopper block As the rotary stopper has three adjusting hex bolts, you can easily obtain three different depths of cut without readjusting the stopper pole. To adjust the hex bolts, loosen the hex nuts on them and turn the hex bolts. After obtaining the desired position, tighten the hex nuts to secure the hex bolts. 1 2 3 4 5 1. Stopper pole Chip deflector Stopper Adjusting hex bolt Hex nut 5 004927 Switch action CAUTION: Before plugging in the tool, always check to see that the tool is switched off. · Make sure that the shaft lock is released before the switch is turned on. Switch lever ASSEMBLY · CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 004928 Installing or removing the bit CAUTION: Install the bit securely. · Do not tighten the collet nut without inserting a bit or install small shank bits without using a collet sleeve. Press the shaft lock to keep the shaft stationary and use the wrench to tighten the collet nut securely. When using router bits with smaller shank diameter, first insert the appropriate collet sleeve into the collet cone, then install the bit as described above. Chip deflector CAUTION: Before operation, always make sure that the tool body automatically rises to the upper limit and the bit does not protrude from the tool base when the lock lever is loosened. · Before operation, always make sure that the chip deflector is installed properly. [. . . ] Vaccum head 10 004940 Push down the lock lever onto the tool base. 1 2 1. Lock lever 004941 Then connect a vacuum cleaner to the vacuum head. Pull the vacuum head out of the tool base while holding the supports between thumb and finger. MAINTENANCE · CAUTION: Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. 001145 Replacing carbon brushes Remove and check the carbon brushes regularly. Limit mark 005111 For tool with the knob Release the lock lever and remove the knob by turning it counterclockwise. [. . . ]