User manual MAKITA MITER SAW LS1030N

[. . . ] Miter Saw Equipped with Electric Blade Brake 255 mm (10") MODEL LS1030N DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. c o m SPECIFICATIONS Blade diameter : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255 mm (10") Hole diameter : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Miter angle : . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Left 45°, Right 52° Max. [. . . ] Turn base 12 001796 Vertical vise The vertical vise can be installed on the guide fence or the holder assembly (optional accessory). Insert the vise rod into the hole in the guide fence or the holder assembly and tighten the screw to secure the vise rod. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle all the way. Position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. CAUTION: The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. 1 2 3 6 4 5 1. Vise arm Vise rod Guide fence Holder Holder assembly Vise knob Screw 7 · 001807 Horizontal vise (optional accessory) The horizontal vise can be installed on either the left or right side of the base. When performing 15° or greater miter cuts, install the horizontal vise on the side opposite the direction in which the turn base is to be turned. By turning the vise knob counterclockwise, the screw is released and the vise shaft can be moved rapidly in and out. To grip the workpiece, turn the vise knob gently clockwise until the projection reaches its topmost position, then fasten securely. If the vise knob is forced in or pulled out while being turned clockwise, the projection may stop at an angle. In this case, turn the vise knob back counterclockwise until the screw is released, before turning again gently clockwise. The maximum width of the workpiece which can be secured by the horizontal vise is 130 mm (5-1/8"). CAUTION: Grip the workpiece only when the projection is at the topmost position. Failure to do so may result in insufficient securing of the workpiece. This could cause the workpiece to be thrown, cause damage to the blade or cause the loss of control, which can result in PERSONAL INJURY. Vise knob Projection Vise shaft Base · 002247 Holders and holder assembly (optional accessories) The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally. Then tighten the screws firmly to secure the holders and the holder assembly. 1 2 1. Holder assembly 002246 2 When cutting long workpieces, use the holder-rod assembly (optional accessory). CAUTION: Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the tool. · 1 1. Rod 12 OPERATION · · · CAUTION: Before use, be sure to release the handle from the lowered position by pulling the stopper pin. [. . . ] La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. 105 Van Nuys, CA 91406 (818) 782-2440 GEORGIA 4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911 NEBRASKA 4129 S. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 TENNESSEE 1120 Elm Hill P. Suile 170 Nashville, TN 372 (615) 248-3321 MARYLAND 7397 Washington Boulevard, Suite 104 Elkridge, MD 21075 (410) 796-4401 NEW JERSEY 251 Herrod Blvd. [. . . ]