User manual MAKITA LS1212

[. . . ] ENGLISH Slide Compound Saw MODEL LS1212 005263 DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Blade diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290 - 305 mm Hole diameter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25. 4 mm Max. Cutting capacities (H x W) Bevel angle Miter angle 45° (left) 0° * 69 mm x 230 mm 61 mm x 298 mm 55 mm x 310 mm * 69 mm x 162 mm 61 mm x 211 mm 55 mm x 220 mm 0° * 120 mm x 230 mm 107 mm x 298 mm 98 mm x 310 mm * 120 mm x 162 mm 107 mm x 211 mm 98 mm x 220 mm * 120 mm x 115 mm 107 mm x 149 mm 98 mm x 155 mm 45° (right) * 49 mm x 230 mm 40 mm x 298 mm 35 mm x 310 mm * 49 mm x 162 mm 40 mm x 211 mm 35 mm x 220 mm - 45° (left and right) 60° (right) (Note) * mark indicates that a wood facing with the following thickness is used. Miter angle 0° 45° (left and right) 60° (right) Thickness of wood 34 mm 24 mm 17 mm No load speed (min-1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3, 200 Dimensions (L x W x H) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 800 mm x 590 mm x 690 mm Net weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] However, when performing left bevel cuts, set it to the left position as shown in the figure 1 1. Sub-fence 11 002261 1 · CAUTION: When performing left bevel cuts, flip the fence over to the left position as shown in the figure. Otherwise, it will contact the blade or a part of the tool, causing possible serious injury to the operator. 1. Sub-fence 002229 Sub-fence R (optional accessory) The sub-fence R should ordinarily be installed on the right side of the guide fence. It will contact the blade or some part of the tool, causing a serious injury to operator. 1 · 2 1. Screws 004068 Vertical vise NOTE: When using the holder assembly, install it on the holder as shown in the figure. Position the vise arm according to the thickness and shape of the workpiece and secure the vise arm by tightening the screw. If the screw to secure the vise arm contacts the guide fence, install the screw on the opposite side of vise arm. Make sure that no part of the tool contacts the vise when lowering the handle fully and pulling or pushing the carriage all the way. Position the workpiece at the desired cutting position and secure it firmly by tightening the clamp screw of the vice. 7. 6 Clamp screw Vise rod Vise arm Guide fence Holder assembly Screw Turn base 7 004069 The maximum thickness of the workpiece which can be secured by the vertical vise is 120 mm. 1 2 1. Vise arm 12 002230 Horizontal vise (optional accessory) The horizontal vise can be installed in two positions on either the left or right side of the base. When performing 15° or greater miter cuts, install the horizontal vise on the side opposite the direction in which the turn base is to be turned. By flipping the vise nut to the left, the vise is released, and rapidly moves in and out. To grip the workpiece, push the vise knob forward until the vise plate contacts the workpiece and flip the vise nut to the right. The maximum width of workpiece which can be secured by the horizontal vise is 200 mm. When installing the horizontal vise on the right side of the base, also use the sub-fence R to secure the workpiece more firmly. Refer to the "Sub-fence R" section described on previously for installing the sub-fence R. CAUTION: Always set the vice nut to the right fully when securing the workpiece. Failure to do so may result in insufficient securing of the workpiece. This could cause the workpiece to be thrown, cause damage to the blade subfence or cause the dangerous loss of control of the tool. 1 2 1. Vise plate Base Vise nut Vise knob 3 4 · 002247 Holders and holder assembly (optional accessories) The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally. [. . . ] Pointer 001569 (1) 1 2 0° bevel angle Push the carriage toward the guide fence and tighten the knob to secure the slide poles. Lower the handle fully and lock it in the lowered position by pushing in the lock pin. Hex bolt 18 001570 Turn the hex bolt on the left side of the arm two or three revolutions counterclockwise. Turn the hex bolt on the right side of the arm two or three revolutions counterclockwise to tilt the blade to the left. 1 1. [. . . ]