User manual MAKITA LS1040

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA LS1040. We hope that this MAKITA LS1040 user guide will be useful to you.


MAKITA LS1040 : Download the complete user guide (883 Ko)

You may also download the following manuals related to this product:

   MAKITA LS1040 (705 ko)
   MAKITA LS1040 (431 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (672 ko)
   MAKITA LS1040 (705 ko)
   MAKITA LS1040 (705 ko)
   MAKITA LS1040 ANNEXE 520 (672 ko)
   MAKITA LS1040 ANNEXE 971 (672 ko)
   MAKITA LS1040 ANNEXE 512 (699 ko)
   MAKITA LS1040 PARTS (473 ko)
   MAKITA LS1040 DC24WA (295 ko)
   MAKITA LS1040 SHEMATICS (134 ko)
   MAKITA LS1040 ANNEXE 409 (672 ko)
   MAKITA LS1040 ANNEXE 958 (699 ko)
   MAKITA LS1040 PARTS LIST 01-2003 (134 ko)
   MAKITA LS1040 PARTS LIST 03-2010 (473 ko)

Manual abstract: user guide MAKITA LS1040

Detailed instructions for use are in the User's Guide.

[. . . ] Due to our continuing programme of research and development, the specifications herein are subject to change without notice. â· Note: Specifications may differ from country to country. MAKE WORKSHOP KID PROOF with padlocks, master switches, or by removing starter keys. It will do the job better and safer at the rate for which it was designed. [. . . ] To install the blade, mount it carefully onto the spindle, making sure that the direction of the arrow on the surface Install the outer flange and hex bolt, and then use the socket wrench to tighten the hex bolt (left-handed) securely counterclockwise while pressing the shaft lock. WARNING: It is extremely important to always secure the workpiece properly and tightly with the vise. Also, after a cutting operation, DO NOT raise the blade until the blade has come to a complete stop. CAUTION: When cutting long workpieces, use supports that are as high as the top surface level of the turn base. Support workpiece over its entire length to avoid blade pinch and possible KICKBACK. Release the handle from the raised position by pulling the stopper pin. The use of the dust bag makes cutting operations clean and dust collection easy. When the dust bag is about half full, remove the dust bag from the tool and pull the fastener out. Empty the dust bag of its contents, tapping it lightly so as to remove particles adhering to the insides which might hamper further collection. position the workpiece at the desired cutting position and secure it firmly by tightening the vise knob. CAUTION: The workpiece must be secured firmly against the turn base and guide fence with the vise during all operations. The holders and the holder assembly can be installed on either side as a convenient means of supporting workpieces horizontally. When cutting long workpieces, use the holder-rod assembly (optional accessory). CAUTION: Always support long workpieces level with the top surface of the turn base for accurate cuts and to prevent dangerous loss of control of the tool. CAUTION: Before use, be sure to release the handle from the lowered position by pulling the stopper pin. Too much force may result in overload of the motor and/or decreased cutting efficiency. Push down handle with only as much force as is necessary for smooth cutting and without significant decrease in blade speed. If the handle is pressed down with force or if lateral force is applied, the blade will vibrate and leave a mark (saw mark) in the workpiece and the precision of the cut will be impaired. Loosen the lever and tilt the saw blade to set the bevel angle (Refer to the previously covered "Adjusting the bevel angle"). Switch on the tool without the blade making any contact and wait until the blade attains full speed. Then gently lower the handle to the fully lowered position while applying pressure in parallel with the blade. When the cut is completed, switch off the tool and WAIT UNTIL THE BLADE HAS COME TO A COMPLETE STOP before returning the blade to its fully elevated position. [. . . ] After replacing brushes, plug in the tool and break in brushes by running tool with no load for about 10 minutes. Then check the tool while running and electric brake operation when releasing the switch trigger. If electric brake is not working well, ask your local Makita service center for repair. After use, wipe off chips and dust adhering to the tool with a cloth or the like. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA LS1040




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA LS1040 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.