User manual MAKITA LD100P

[. . . ] The Makita LD100P is designed for use in areas permanently habitable by humans, do not use the product in explosion hazardous areas or in aggressive environments. To be familiar with local safety regulations relating to accident prevention. Care for the environment and take them to the collection points provided in accordance with national or local regulations. Dispose of the product appropriately in accordance with the national regulations in force in your country. [. . . ] However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: · Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. ⷠConsult the dealer or an experienced radio/TV technician for help WARNING: Changes or modifications not expressly approved by Makita for compliance could void the user's authority to operate the equipment. The Makita LD100P produces a visible laser beam which emerges from the front of the instrument. it is a Class 2 laser product in accordance with: · IEC60825-1 : 2007 "Radiation safety of laser products" Laser Class 2 products: Do not stare into the laser beam or direct it towards other people unnecessarily. eye protection is normally afforded by aversion responses including the blink reflex. Remove the batteries before any long period of non-use to avoid the danger of corrosion. See figure {B} The instrument can be adapted for the following measuring situations: · For measurements from an edge, fold out the positioning bracket until it first locks in place. For measurements from a corner, open the positioning bracket until it locks in place, then push the positioning bracket lightly to the right to fold it out fully. 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 Double (partial height) measurement Illumination Save constant value, call up constant value Historical memory, call up values Battery status Timer Area/volume Tilt Horizontal distance measurement using tilt Room corner angle function Menu Continuous laser Reset Reference (tripod) Beep Circumference Wall area Ceiling area Intermediate line 1 Intermediate line 2 Intermediate line 3 Summary line See figure {E}: 1 2 3 4 5 6 7 8 9 10 11 ON (On/measuring) button Plus (+) button Minus (-) button Functions button Area / volume button Equal / menu button Memory button Indirect measurement (Pythagoras) button Clear / off button Timer button Reference button See figure {F} 1 2 3 4 5 6 7 8 Laser active Reference (front) Reference (rear) Reference (corner stop) Measuring with the tripod Stake out function Single Pythagorean measurement Double Pythagorean measurement After switching off the device or replacing the batteries the settings are stored. Setting the unit for distance measurements The following units can be set: 1. The angles in a triangle can be calculated by measuring the three sides. Press this button three times and the room corner symbol appears in the display . mark the reference points to the right and left (d1/ d2) of the angle to be measured. Press this button to measure the first (short) side of the triangle (d1 or d2). Press this button to measure the second (short) side of the triangle (d1 or d2). Press this button to measure the third (long) side of the triangle (d3). By using and , you can adjust the values (first a and then b) to suit the desired stake out distances. Once the desired value (a) has been reached it can be confirmed with the button. the value (b) and the intermediate line flashes (the defined value (a) is automatically adopted). The display shows required stake out distance In the summary line between the stake out point (first a and then b) and the instrument (rear reference). If the Makita LD100P is then moved slowly along the stake out line the displayed distance decreases. [. . . ] Press and hold down this button to trigger continuous measurement, sweep the laser back and forth and up and down over the ideal target point. Determining the height between point 1 and point 2 using three target points. Press this button three times ; the display shows the following symbol . See figure {N} Press this button twice; the display shows the following symbol . [. . . ]