User manual MAKITA KP0800K

[. . . ] Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. [. . . ] An exposed cutter may engage the surface leading to possible loss of control and serious injury. Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. Release the switch trigger to stop. Foot CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. Knob 010173 1 2 3 2 010336 After a cutting operation, raise the back side of the tool and a foot comes under the level of the rear base. This prevents the tool blades to be damaged. ASSEMBLY · Depth of cut may be adjusted by simply turning the knob on the front of the tool so that the pointer points the desired depth of cut. Switch action 1 2 CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 1. Switch trigger Removing or installing planer blades CAUTION: Tighten the blade installation bolts carefully when attaching the blades to the tool. Use gloves or rags to protect your fingers or hands when removing or installing the blades. · Use only the Makita wrench provided to remove or install the blades. Failure to do so may result in overtightening or insufficient tightening of the installation bolts. For tool with conventional planer blades · 010172 CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. For tool with lock button · CAUTION: · Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. Set the adjusting plate/set plate on the gauge base so that the planer blade locating lugs on the set plate rest in the mini planer blade groove, then press in the heel of the adjusting plate flush with the back side of the gauge base and tighten the pan head screws. It is important that the blade sits flush with the inside flank of the gauge plate, the planer blade locating lugs sit in the blade groove and the heel of the adjusting plate is flush with the back side of the gauge base. Slip the heel of the adjusting plate into the groove of the drum. 1 6 5 4 3 2 7 1. Adjusting plate 002566 6. 002564 1. Remove the existing blade, if the tool has been in use, carefully clean the drum surfaces and the drum cover. To remove the blades on the drum, 6 Set the drum cover over the adjusting plate/set plate and screw in the three hex flange head bolts so that a gap exists between the drum and the set plate to slide the mini planer blade into position. The blade will be positioned by the planer blade locating lugs on the set plate. 7. 8. 9. The blade's lengthwise adjustment will need to be manually positioned so that the blade ends are clear and equidistant from the housing on one side and the metal bracket on the other. Tighten the three hex flange head bolts (with the socket wrench provided) and rotate the drum to check clearances between the blade ends and the tool body. [. . . ] Screwdriver 2 010185 Use a screwdriver to remove the chip cover or nozzle. 002590 Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the both blades contact the dressing stone for simultaneous sharpening at the same angle. 1. Limit mark 010186 1 2 1 001145 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. [. . . ]