User manual MAKITA JIG SAW 4305T

[. . . ] When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 2 14. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. A n undersized cord will cause a drop in line voltage resulting in loss of power and overheating. [. . . ] To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to help determine the appropriate cutting action. I Position 0 Cutting action Straight line cutting action Applications For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood. 1 I I1 I Small orbit cutting action Medium orbit cutting action I For cutting mild steel, aluminum and hard wood For cutting wood and plywood. For fast cutting in aluminum and mild steel. I 6 111 I Large orbit cutting action I For fast cutting in wood and plywood. Switch action For 4304T CAUTION : Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. To start the tool, simply pull the trigger. For continuous operation, pull the trigger and move the lock lever backward. To stop the tool from the locked position, pull the trigger fully, then release it. ILock lever Switch trigger For 4305T CAUTION: Before plugging in the tool, always check to see that the switch actuates properly. Slide the switch lever backward to stop. Speed adjusting dial The tool speed can be adjusted and maintained between 500 and 3, 000 strokes per minute by turning the adjusting dial. The dial i s marked 1 (lowest speed) to 6 (full speed). For 4304T Speed adjusting dial I For 4305T Speed adjusting dial Refer to the table a t right to Select the Proper speed for the workpiece to be cut. However, the appropriate speed may differ with the type or thickness of the workpiece. In general, higher speeds will allow you to cut workpieces faster but the service life of the blade will be reduced. Mild Steel Stainless Steel Aluminum Plastics CAUTION : Adjust the speed adjusting dial only within the range of numbers 1 through 6. Do not force the dial beyond this range or damage to the tool may result. Cutting operation CAUTION : 0 Always hold the tool with the base flush with the workpiece. Failure to do so may cause a slanted cutting surface and blade breakage. Forcing the tool may cause a slanted cutting surface and blade breakage. Rest the base flat on the workpiece and gently move the tool forward along the previously marked cutting line. Cutting line Bevel cutting CAUTION : Always unplug the tool before making any adjustments. ' With the base tilted, you can make bevel cuts at any angle between 0 and 45' (left or right). Loosen the base securing lever and move the base so that the dent mark in the motor housing is aligned with the slot in the base. The edge of the motor housing indicates the bevel angle by graduations. Then tighten the base securing lever to secure the base. NOTE : Always remove the plastic cover (chip shield) from the tool when you make bevel cuts using an optional guide rule (rip fence) or circular guide. . Base securing lever 8 Flush cutting Loosen the base securing lever and slide the base all the way back. Then tighten the base securing lever to secure the base. cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cutouts without a lead-in cut from and edge, pre-drill starting hole more than 12 mm (15/32") in diameter. Install the plastic cover on the tool by fitting it into the notches in the tool. 1 7 - Vacuum head I Base To attach the vacuum head on the tool, insert the hook of the vacuum head into the hole in the base. [. . . ] Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply where: repairs have been made or attempted by others: a repairs are required because of normal wear and tear: a The tool has been abused, misused or improperly maintained ; alterations have been made to the tool. IN NO EVENT SHALL MAKlTA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE O F THE PRODUCT. [. . . ]