User manual MAKITA HR5000K

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA HR5000K. We hope that this MAKITA HR5000K user guide will be useful to you.


MAKITA HR5000K : Download the complete user guide (246 Ko)

You may also download the following manuals related to this product:

   MAKITA HR5000K (251 ko)
   MAKITA HR5000K (251 ko)
   MAKITA HR5000K (251 ko)
   MAKITA HR5000K (251 ko)
   MAKITA HR5000K ANNEXE 341 (118 ko)
   MAKITA HR5000K ANNEXE 637 (118 ko)

Manual abstract: user guide MAKITA HR5000K

Detailed instructions for use are in the User's Guide.

[. . . ] 8 9 10 11 12 13 14 For hammering only Switch trigger Core bit Adapter Center bit Rod Hex wrench 15 16 17 18 19 20 Rear cover Screwdriver Brush holder cap Lock nut wrench Crank cap Hammer grease Due to our continuing program of research and development, the specifications herein are subject to change without notice. ⷠNote: Specifications may differ from country to country. Power supply The tool should be connected only to a power supply of the same voltage as indicated on the nameplate, and can be operated on single-phase AC/DC supply. [. . . ] The side grip can be installed on either side of the tool for right or left hand operation. Important: Always be sure that the tool is switched off and unplugged before installing or removing the bit. CAUTION: When the bit begins to break through concrete or if the bit strikes reinforcing rods embedded in concrete, the tool may react dangerously. Maintain good balance and safe footing while holding the tool firmly with both hands to prevent dangerous reaction. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Once the core bit has cut a shallow groove into the concrete, remove the center bit. 8) (2) Hold the adapter with the wrench, insert the rod (optional accessory) into the hole in the core bit and tap with a hammer to unscrew. Once the core bit has cut a shallow groove into the concrete, rotate the change lever to the position and resume drilling. NOTE: No problem is caused even if the core bit unscrews slightly during brief use since the core bit rotates in the tightening direction. To remove the core bit, follow the same removal procedures covered in When using the center bit. To avoid rapid wear on the mode change mechanism, be sure that the change lever is always positively located in one of the two action mode positions. Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. ⷠDo not tape, tie or otherwise secure the trigger in the "ON" position. Keep the tool in position and prevent it from slipping away from the hole. [. . . ] : series production) manufactured by Makita Corporation in Japan is in compliance with the following standards or standardized documents, HD400, EN50144, EN55014, EN61000 in accordance with Council Directives, 73/23/EEC, 89/336/EEC and 98/37/EC. The typical A-weighted noise levels are sound pressure level: 95 dB (A) sound power level: 108 dB (A) ­ Wear ear protection. The typical A-weighted noise levels are sound pressure level: 95 dB (A) sound power level: 108 dB (A) ­ Wear ear protection. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA HR5000K




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA HR5000K will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.