User manual MAKITA BTP140RFE

[. . . ] ENGLISH Cordless 4 Mode Impact Driver MODEL BTP130 MODEL BTP140 007155 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. SPECIFICATIONS Model Max. fastening torque Machine screw Capacities Impact driver mode Standard bolt High tensile bolt No load speed (min ) Impacts per minute No load speed (min-1) Hammer drill mode Blows per minute Capacities No load speed (min-1) Concrete High (2) Low (1) High (2) Drill mode Capacities High (2) Wood Low (1) Screw driver mode No load speed (min-1) Capacities Overall length Net weight Rated voltage 1. 7 kg D. C. 14. 4 V Machine screw 0 - 2, 400 M4 186 mm 1. 8 kg D. C. 18 V 21 mm 0 -2, 300 9 mm Steel Low (1) 10 mm 0 - 2, 400 0 - 700 6. 5 mm 0 - 2, 400 0 - 28, 800 8 mm 0 - 2, 300 -1 BTP130 135 N·m 4 mm - 8 mm 5 mm - 14 mm 5 mm - 12 mm 0 - 2, 400 0 - 3, 200 BTP140 140 N·m 0 - 2, 300 0 - 2, 300 0 - 27, 600 · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. · Note: Specifications may differ from country to country. END001-1 Symbols The following show the symbols used for the equipment. [. . . ] 3. 4. 5. 5 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 006667 Installing or removing battery cartridge · · · Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, withdraw it from the tool while sliding the button on the front of the cartridge. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If you can see the red part on the upper side of the button, it is not locked completely. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. Action mode changing lever 007159 For rotation with hammering, turn the lever so that the arrow points toward the mark on the tool body. 1 1. Action mode changing lever 007160 For rotation with clutch, turn the lever so that the arrow points toward the mark on the tool body. 1 1. Action mode changing lever 007161 For rotation only, turn the lever so that the arrow on the lever points toward the mark or the mark on the tool body. 1 1. Action mode changing lever 7 007162 Sliding to the mark is high rotation and the mark is low rotation. Before operation, always make sure that the lever is correctly set to your desired mode mark and use the tool at an appropriate speed for your work. CAUTION: When using the action mode change lever, use only when the tool stops. But when the lever does not easily move, pull the switch trigger slightly to rotate the spindle and then move the lever. If you operate the tool with the lever positioned halfway between the mode marks, the tool may be damaged. · 1 1. Action mode changing lever · 007163 Adjusting the fastening torque (Only for screwdriving operation mode " ") The fastening torque can be adjusted in 16 steps by turning the adjusting ring so that its graduations are aligned with the pointer on the tool body. The fastening torque is minimum when the number 1 is aligned with the pointer, and maximum when the number 16 is aligned with the pointer. The clutch will slip at various torque levels when set at the number 1 to 16. Before actual operation, drive a trial screw into your material or a piece of duplicate material to determine which torque level is required for a particular application. NOTE: · In modes other than screwdriving mode, the adjusting ring can be placed at any position because it does not work. 1 3 1. Pointer 2 ASSEMBLY · CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool. 004521 Installing or removing driver bit or socket bit Use only the driver bit or socket bit shown in the figure. For European and North & South American countries, Australia and New Zealand 006348 A=12mm Use only these type of bit. B=9mm (Note) Bit-piece is not necessary. 8 For other countries 006349 A=17mm To install these types of bits, follow the procedure (1). [. . . ] If the tool is operated continuously until the battery cartridge has discharged, allow the tool to rest for 15 minutes before proceeding with a fresh battery. · · NOTE: · When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart. 006421 Nominal diameter of wood screw (mm) 3. 1 3. 5 3. 8 4. 5 4. 8 5. 1 5. 5 5. 8 6. 1 Recommended size of pilot hole (mm) 2. 0 - 2. 2 2. 2 - 2. 5 2. 5 - 2. 8 2. 9 - 3. 2 3. 1 - 3. 4 3. 3 - 3. 6 3. 7 - 3. 9 4. 0 - 4. 2 4. 2 - 4. 4 Drilling operation First, set the action mode changing lever so that the pointer points to to the mark or the mark. The adjusting ring can be aligned in any torque levels for this operation. Before operation, always make sure that the lever is correctly set to your desired mode mark and use the tool at an appropriate speed for your work. [. . . ]