User manual MAKITA BTD145RFE

[. . . ] Unmodified plugs and matching outlets will reduce risk of electric shock. Avoid body contact with earthed or grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded. Never use the cord for carrying, pulling or unplugging the power tool. [. . . ] It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 C (122 F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. Do not use a damaged battery. FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 2. Lamp This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. · · 1 009209 · 1. Light button S H 1 011216 Every time the light button on the switch panel is pressed, the light status is alternatively changed from the ON to the OFF and from the OFF to the ON. With the light button in the ON status, pull the switch trigger to turn on the light. To turn off, release it and the light goes out approximately 10 seconds after releasing. 6 Changing the hammering force 2 3 S H 1 S S H H 4 011217 S H 5 1. Hammering force button Hammering force grade displayed on panel Hard S H Maximum blows BTD133 BTD145 Application Work 3, 200 (min -1) 3, 400 Tightening when force (min -1) and speed are desired. Tightening in underwork material/ Tightening long screws/ Tightening bolts. Medium S H 2, 600 (min -1) 2, 800 (min -1) Tightening when a good finishing is needed. Tightening in the finishing board, plaster board. Soft S H 1, 100 (min -1) 1, 300 (min -1) Tightening when excessive tightening need to be avoided because of potentially clogged female screw and broken or damaged screw head. Tightening sash screw/ Tightening small screws such as M6. 011189 The hammering force can be changed in three steps: hard, medium and soft. Every time the hammering force button is pressed, the number of blows changes in three steps. For approximately one minute after releasing the switch trigger, the hammering force can be changed. NOTE: · When all lamps on the switch panel go out, the tool is turned off to save the battery power. [. . . ] When the LED indicator still lights up even after charging the battery cartridge, the tool temperature is high. When the status is still unchanged, stop using and have the tool repaired by a Makita local service center. (When the tool has stopped due to the motor locking, withdraw the battery cartridge one time and then insert it again or release the switch trigger for more than 60 seconds to restart the tool. ) If the motor still remains locked, stop using and have the tool repaired by a Makita local service center. Stop using and have the tool repaired by a Makita local service center. Light status/LED indicator status/tool status LED indicator for empty signal for remaining battery capacity lights up. Light flickers once per second. [. . . ]