User manual MAKITA BHR261TRDE

[. . . ] ENGLISH (Original instructions) INSTRUCTION MANUAL Cordless Combination Hammer BHR261 BHR261T 009665 IMPORTANT: Read Before Using. 1 ENGLISH (Original instructions) SPECIFICATIONS Model Concrete Capacities No load speed (min-1) Blows per minute Overall length Net weight Rated voltage · Note: Specifications and battery cartridge may differ from country to country. · Weight, with battery cartridge, according to EPTA-Procedure 01/2003 END004-4 BHR261 26 mm 13 mm 32 mm 0 - 1, 200 0 - 4, 800 363 mm 4. 5 kg D. C. 36 V Steel Wood BHR261T 387 mm 4. 7 kg · Due to our continuing programme of research and development, the specifications herein are subject to change without notice. Model BHR261T Sound pressure level (LpA) : 92 dB(A) Sound power level (LWA) : 103 dB(A) Uncertainty (K) : 3 dB(A) Wear ear protection ENG900-1 Symbols The following show the symbols used for the equipment. Read instruction manual. Cd Ni-MH Li-ion Only for EU countries Do not dispose of electric equipment or battery pack together with household waste material! [. . . ] If the cartridge does not slide in easily, it is not being inserted correctly. CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Release the switch trigger to stop. · Lighting up the lamp 1. Lamp 1 009668 Battery protection system The battery cartridge is equipped with the protection system, which automatically cuts off the output power for its long service life. The tool may stop during operation when the tool and/or battery are placed under the following situation. This is caused by the activation of protection system and does not show the tool trouble. · When the tool is overloaded: At this time, release the switch trigger and remove causes of overload and then pull the 6 CAUTION: Do not look in the light or see the source of light directly. The light automatically goes out 10 - 15 seconds after the switch trigger is released. · NOTE: · Use a dry cloth to wipe the dirt off the lens of lamp. Be careful not to scratch the lens of lamp, or it may lower the illumination. Change cover 3 4 009685 1 2 A B 1 009669 This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. Check the line of the quick change drill chuck shows the symbol. Grasp the change cover of the quick change drill chuck and set the line to the symbol. Grasp the change cover of the quick change drill chuck and turn the change cover line to the symbol until a click can clearly be heard. · · Selecting the action mode Rotation with hammering 1. Rotation with hammering · Changing the quick change chuck for SDS-plus For model BHR261T The quick change chuck for SDS-plus can be easily exchanged for the quick change drill chuck. Change cover line 2 3 For drilling in concrete, masonry, etc. , depress the lock button and rotate the action mode changing knob to the symbol. Rotation only 009684 CAUTION: · Before removing the quick change chuck for SDS-plus, always remove the bit. Grasp the change cover of the quick change chuck for SDS-plus and turn in the direction of the arrow until the change cover line moves from the symbol to the symbol. Pull forcefully in the direction of the arrow. 1 009671 For drilling in wood, metal or plastic materials, depress the lock button and rotate the action mode changing knob to the symbol. Hammering only CAUTION: Always use the side grip to ensure operating safety. [. . . ] Change cover 1 2 009680 Set the action mode changing knob to the symbol. Turn the tool on and apply slight pressure on the tool so that the tool will not bounce around, uncontrolled. Pressing very hard on the tool will not increase the efficiency. 1. Change cover 4 3 009928 Drilling in wood or metal For model BHR261 only 1 1 1. [. . . ]