User manual MAKITA 98202

[. . . ] Make sure switch is in off position before plugging in. . L 17. Serious injury could occur if the tool is tipped or if the cutting tool is accidentally contacted. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function - check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced. [. . . ] A temporary adapter, which looks like the adapter illustrated in Figure B and C, may be used t o connect this plug t o a 2-pole receptacle as shown in Figure B if a properly grounded outlet is not available. The temporary adapter should be used only until a properly grounded outlet can be installed by a qualified electrician. extending from the adapter must be connected t o a permanent ground such as a properly grounded outlet box. . . GROUNDING METHODS FIG. C Adapter Q I Grounding Pin -Cover of Grounded Outlet Box Grounding Means 4 ADDITIONAL SAFETY RULES 1. Use only wheels having a maximum operating speed at least as high as "No Load RPM" marked on the tool's nameplate. Be careful not t o damage the spindle or the bolt, or the wheel itself might break. Keep a space of 5 m m (3/16") between the sharpening platform guide (rail) and the grinding wheel. Make sure the workpiece is not contacting the wheel before the switch is turned on. Before using the tool on an actual workpiece, let it run for several minutes. Watch for flutter that might be caused by incorrect installation or a poorly balanced wheel. If the wheel stops during operation, makes an odd noise o begins t o vibrate, r switch off the tool immediately. 11. Always switch off and wait for the wheel t o come t o a complete stop before adjustment or inspection. Do not touch the workpiece immediately after operation, it may be extremely hot and could burn your skin. Dry the wheel by idling the tool after operation t o prevent the wheel from freezing in cold weather. Store wheels in a dry location only. SAVE THESE INSTRUCTIONS. WARNING For Your Own Safety Read Instruction Manual Before Operating Grinder 1. Use only flanges furnished with the grinder. 5 HOW TO USE Replacing grinding wheel Use the wrench provided to release the grinding wheel by turning the installation screw counterclockwise. To install the grinding wheel, follow the removal procedure in reverse. Adjusting wheel guard The top of the wheel guard should be 1 mm (approx. Adjust height by turning the guard clockwise to lower it, or counterclockwise to raise it. Wiping off the antirust Wipe off the antirust on the sharpening platform guide (rail) and the sharpening holder. Coat the sharpening platform guide and the sharpening holder with machine oil or spindle oil. Removing or installing sharpening platform guide To remove the sharpening platform guide, loosen the screw and slip the set plate aside. 6 Loosen the pole fastening screws and lift off the sharpening platform guide. To install the sharpening platform guide, follow the removal procedure in reverse. Adjusting sharpening platform guide In using the sharpening platform guide to sharpen blade/knife, adjust the angle adjustment screw to the desired blade/knife sharpening angle. The bevel becomes acute as the angle adjustment screw is turned clockwise. Sharpening platform guide (Rail) The platform poles are fixed in place by tightening the pole fastening screws on either side. Pole 7 The nut for raising or lowering the pole on either side raises the pole 0. 5 mm (1/32") for each graduation, when turned clockwise, and it lowers the pole, conversely, 0. 5 mm (1/32") when turned counterclockwise. Tilt the sharpening platform guide slightly with right side downward so that the blade contacts the right side surface of the grinding wheel. Adjusting sharpening holder I The sharpening holder horizontal (forward) adjust screws should be unscrewed to allow the heel of the blade to be inserted so as to contact the blade fastening screws. Then lightly tighten the blade fastening screws and set the holder on the platform. Blade - I I Forward adiurt screw \ \ I I 8 Screw in clockwise the forward adjust screw on the right until the right upper edge of the blade comes into contact with the grinding wheel. [. . . ] The accessories or attachments should be used only in the proper and intended manner. 0 Grinding wheels Wrench Part No. 341 391 - 3 Size (mm) 200x25~75 (7-7/8" x 1 " x 3 " ) I Grit I Part No. Guide assembly (Sharpening platform guide) For sharpening scissors or knife. This Warranty does not apply where: repairs have been made or attempted by others: repairs are required because of normal wear and tear: 0 The tool has been abused, misused or improperly maintained; alterations have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. [. . . ]