User manual MAKITA 9047F

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 9047F. We hope that this MAKITA 9047F user guide will be useful to you.


MAKITA 9047F : Download the complete user guide (240 Ko)

You may also download the following manuals related to this product:

   MAKITA 9047F (287 ko)
   MAKITA 9047F (287 ko)
   MAKITA 9047F (287 ko)
   MAKITA 9047F (287 ko)
   MAKITA 9047F ANNEXE 575 (165 ko)
   MAKITA 9047F ANNEXE 606 (165 ko)

Manual abstract: user guide MAKITA 9047F

Detailed instructions for use are in the User's Guide.

[. . . ] They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire. for models 9047 , 9049 , 9057 and 9059 , public low-voltage distribution systems of between 220 V and 250 V Switching operations of electric apparatus cause voltage fluctuations. The operation of this device under unfavorable mains conditions can have adverse effects to the operation of other equipment. [. . . ] When using depressed center wheels, be sure to use only fiberglass-reinforced wheels. When installing a depressed center wheel or an abrasive cut-off wheel, always use a wheel guard. Mount the wheel guard with the tab on the wheel guard band aligned with the notch on the bearing box. The side grip can be installed in any of three positions on the sides of the tool, whichever is convenient and keeps the guard properly positioned. Always hold the tool's switch handle and the side grip firmly with both hands during operation. For other countries than the above countries To start the tool, simply pull the trigger. For continuous operation, pull the trigger and then push the lock lever. To stop the tool from the locked position, pull the trigger fully, then release it. NOTE: Models 9047S, 9057S, 9049S, 9059S, 9047SF, 9057SF, 9049SF and 9059SF begin to run slowly when they are turned on. This soft start feature assures smoother operation and less operator fatigue. Important: Always be sure that the tool is switched off and unplugged before installing or removing the wheel. Fit the wheel on over the inner flange and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. NOTE: Super flange Models 9047F, 9057F, 9049F, 9059F, 9047SF, 9057SF, 9049SF and 9059SF are standard-equipped with a super flange. Only 1/3 of efforts needed to undo lock nut, compared with conventional type. In general, keep the edge of the wheel or disc at an angle of about 15° ­ 30° to the workpiece surface. During the break-in period with a new wheel, do not work the tool in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions. [. . . ] To maintain product safety and reliability, repairs, maintenance or adjustment should be carried out by Makita Authorized Service Center. Is in compliance with the following standards or standardized documents, HD400, EN50144, EN55014, EN61000 in accordance with Council Directives, 73/23/EEC, 89/336/EEC and 98/37/EC. The typical A-weighted noise levels are sound pressure level: 90 dB (A) sound power level: 103 dB (A) ­ Wear ear protection. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 9047F




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 9047F will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.