User manual MAKITA 8391DWPE

[. . . ] There is an increased risk of electric shock if your body is earthed or grounded. Never use the cord for carrying, pulling or unplugging the power tool. 2 Intended use The tool is intended for impact drilling in brick, concrete and stone as well as for drilling without impact in wood, metal, ceramic and plastic. GEA006-2 General Power Tool Safety Warnings WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. When operating a power tool outdoors, use an extension cord suitable for outdoor use. [. . . ] Do not touch the bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. 4. 5. 6. 7. 8. 9. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. Always cover the battery terminals with the battery cover when the battery cartridge is not used. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50 C (122 F). Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. Be careful not to drop or strike battery. SAVE THESE INSTRUCTIONS. Tips for maintaining maximum battery life 1. Always stop tool operation and charge the battery cartridge when you notice less tool power. Charge the battery cartridge with room temperature at 10 C - 40 C (50 F - 104 F). Charge the Nickel Metal Hydride battery cartridge when you do not use it for more than six months. SAVE THESE INSTRUCTIONS. WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. ENC004-1 2. 3. IMPORTANT SAFETY INSTRUCTIONS FOR BATTERY CARTRIDGE 1. Before using battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using battery. Do not disassemble battery cartridge. 4. 2. 4 FUNCTIONAL DESCRIPTION · Reversing switch action 1. Reversing switch lever CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. A 1 008696 B Installing or removing battery cartridge 1 1. Battery cartridge 2 008694 This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. [. . . ] Place the point of the driver bit in the screw head and apply pressure to the tool. CAUTION: Make sure that the driver bit is inserted straight in the screw head, or the screw and/or bit may be damaged. · · · · · NOTE: · When driving wood screws, predrill pilot holes to make driving easier and to prevent splitting of the workpiece. See the chart. Nominal diameter of wood screw (mm) 3. 1 3. 5 3. 8 4. 5 4. 8 5. 1 5. 5 5. 8 6. 1 006421 MAINTENANCE CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance. To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts. · Recommended size of pilot hole (mm) 2. 0 - 2. 2 2. 2 - 2. 5 2. 5 - 2. 8 2. 9 - 3. 2 3. 1 - 3. 4 3. 3 - 3. 6 3. 7 - 3. 9 4. 0 - 4. 2 4. 2 - 4. 4 ACCESSORIES · Drilling operation First, turn the adjusting ring so that the pointer points to the marking. [. . . ]