User manual MAKITA 6918FDWDE

[. . . ] Cordless Impact Wrench MODEL 6918FD 004403 INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. c o m SPECIFICATIONS Model Capacities Standard bolt High tensile bolt Square drive No load speed (RPM) Impacts per minute Max. fastening torque Overall length Net weight Battery Cartridge 1222 1234 1235 12 V DC1414 A. 7. 2 V - 14. 4 V Voltage Battery Charger Input 6918FD M8 - M14 (5/16" - 9/16") M6 - M12 (1/4" - 1/2") 12. 7mm (1/2") 0 - 2, 300/min. [. . . ] Do not attempt to use a step-up transformer, an engine generator or DC power receptacle. Always cover the battery terminals with the battery cover when the battery cartridge is not used. Do not short the battery cartridge: (1) Do not touch the terminals with any conductive material. (2) Avoid storing battery cartridge in a container with other metal objects such as nails, coins, etc. A battery short can cause a large current flow, overheating, possible burns and even a breakdown. Do not store the tool and Battery Cartridge in locations where the temperature may reach or exceed 50°C (122°F). 6 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery must be placed in a well ventilated area during charging. SAVE THESE INSTRUCTIONS 7 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking function on the tool. 004392 Installing or removing battery cartridge · · Always switch off the tool before insertion or removal of the battery cartridge. To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. If the cartridge does not slide in easily, it is not being inserted correctly. 1 2 1. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. When the charging light color changes from red to green, the charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode. After charging, unplug the charger from the power source. 8 NOTE: · The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. [. . . ] La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. 105 Van Nuys, CA 91406 (818) 782-2440 GEORGIA 4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911 NEBRASKA 4129 S. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 TENNESSEE 1120 Elm Hill P. Suile 170 Nashville, TN 372 (615) 248-3321 MARYLAND 7397 Washington Boulevard, Suite 104 Elkridge, MD 21075 (410) 796-4401 NEW JERSEY 251 Herrod Blvd. [. . . ]