User manual MAKITA 6405

[. . . ] Avoid body contact with grounded surfaces such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is grounded. Never use the cord to carry the tools or pull the plug from an outlet. When operating a power tool outside, use an outdoor extension cord marked "W-A" or "W". [. . . ] Table 1 shows the correct size to use depending on cord length and nameplate ampere rating. The smaller the gage number, the heavier the cord. Table 1: Minimum gage for cord Ampere Rating More Than 0 6 10 12 Not More Than 6 10 12 16 18 18 16 14 Volts 120 V 25 ft. AWG 16 16 16 12 16 14 14 12 14 12 Not Recommended 4 SPECIFIC SAFETY RULES USB001-2 DO NOT let comfort or familiarity with product (gained from repeated use) replace strict adherence to drill safety rules. If you use this tool unsafely or incorrectly, you can suffer serious personal injury. 1. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a "live" wire will make exposed metal parts of the tool "live" and shock the operator. Do not touch the drill bit or the workpiece immediately after operation; they may be extremely hot and could burn your skin. Follow material supplier safety data. SAVE THESE INSTRUCTIONS WARNING: MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury. 5 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 003014 Switch action · CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Switch can be locked in "ON" position for ease of operator comfort during extended use. Apply caution when locking tool in "ON" position and maintain firm grasp on tool. 1 2 · 1. For continuous operation, pull the switch trigger and then push in the lock button. To stop the tool from the locked position, pull the switch trigger fully, then release it. 003024 Reversing switch action This tool has a reversing switch to change the direction of rotation. Move the reversing switch lever to the "FWD" position for clockwise rotation or the "REV" position for counterclockwise rotation. 1 1. Reversing switch lever When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. Pulling the trigger hard when the reversing switch lever is in the neutral position can cause switch breakage. · · · · 6 ASSEMBLY · CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. 003048 Installing or removing drill bit To install the bit, place it in the chuck as far as it will go. To remove the bit, turn the chuck key counterclockwise in just one hole, then loosen the chuck by hand. After using the chuck key, be sure to return to the original position. 1 1. Chuck key OPERATION Drilling operation Drilling in wood When drilling in wood, the best results are obtained with wood drills equipped with a guide screw. The guide screw makes drilling easier by pulling the bit into the workpiece. [. . . ] Should any trouble develop during this one year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply where: · repairs have been made or attempted by others: · repairs are required because of normal wear and tear: · the tool has been abused, misused or improperly maintained: · alterations have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. [. . . ]