User manual MAKITA 6343DWDE

[. . . ] Cordless Driver Drill Equipped with Electric Brake MODEL 6343D INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. c o m SPECIFICATIONS Model Steel Capacities Wood Wood screw Machine screw No load speed (RPM) Dimensions (L x W x H) Net weight Battery Charger Input Output Battery Cartridge Voltage Charging time 45 min. 1834 1835 High Low 6343D 13 mm (1/2") 38 mm (1-1/2") 10 x 89 mm (3/8" x 3-1/2") 6 mm (1/4") 0 - 1, 400/min. 255 mm x 95 mm x 249 mm (10-1/32" x 3-3/4" x 9-13/16") 2. 5 kg (5. 5 lbs) · Manufacturer reserves the right to change specifications without notice. [. . . ] To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Always insert it all the way until it locks in place with a little click. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. If the cartridge does not slide in easily, it is not being inserted correctly. 1 2 1. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. When the charging light color changes from red to green, the charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode. After charging, unplug the charger from the power source. 8 NOTE: · The battery charger is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. If the tool consistently fails to quickly stop after switch trigger release, have tool serviced at a Makita service center. 002086 Reversing switch action This tool has a reversing switch to change the direction of rotation. Depress the reversing switch lever from the A side for clockwise rotation or from the B side for counterclockwise rotation. When the reversing switch lever is in the neutral position, the switch trigger cannot be pulled. 1 A B 1. Reversing switch lever · · CAUTION: Always check the direction of rotation before operation. Use the reversing switch only after the tool comes to a complete stop. Changing the direction of rotation before the tool stops may damage the tool. When not operating the tool, always set the reversing switch lever to the neutral position. · 002094 Speed change To change the speed, first switch off the tool and then slide the speed change lever to the "II" side for high speed or "I" side for low speed. Be sure that the speed change lever is set to the correct position before operation. CAUTION: Always set the speed change lever fully to the correct position. Speed change lever · 10 lever positioned halfway between the "I" side and "II" side, the tool may be damaged. [. . . ] La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. 105 Van Nuys, CA 91406 (818) 782-2440 GEORGIA 4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911 NEBRASKA 4129 S. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 TENNESSEE 1120 Elm Hill P. Suile 170 Nashville, TN 372 (615) 248-3321 MARYLAND 7397 Washington Boulevard, Suite 104 Elkridge, MD 21075 (410) 796-4401 NEW JERSEY 251 Herrod Blvd. [. . . ]