User manual MAKITA 5277B

[. . . ] Hypoid Saw 185 mm (7-1/4") MODEL 5277B DOUBLE INSULATION INSTRUCTION MANUAL WARNING: For your personal safety, READ and UNDERSTAND before using. Cutting depth at 45° at 50° No load speed (RPM) Overall length Net weight 5277B 185 mm (7-1/4") 62 mm (2-3/8") 44 mm (1-23/32") 40 mm (1-9/16") 4, 300/min. 439 mm (17-1/4") 6. 8 kg (15. 0 lbs) · Manufacturer reserves the right to change specifications without notice. · Specifications may differ from country to country. GENERAL SAFETY RULES (For All Tools) USA002-2 WARNING: Read and understand all instructions. [. . . ] When blade is binding, or when interrupting a cut for any reason, release the trigger and hold the saw motionless in the material until the blade comes to a complete stop. Never attempt to remove the saw from the work or pull the saw back- 5 ward while the blade is in motion or KICKBACK may occur. Investigate and take corrective actions to eliminate the cause of blade binding. When restarting a saw in the workpiece, center the saw blade in the kerf and check that saw teeth are not engaged into the material. If saw blade is binding, it may walk up or KICKBACK from the workpiece as the saw is restarted. Support large panels to minimize the risk of blade pinching and KICKBACK. Supports must be placed under the panel on both sides, near the line of cut and near the edge of the panel as shown in Fig. When cutting operation requires the resting of the saw on the workpiece, the saw should be rested on the larger portion and the smaller piece cut off. sharp and clean. Gum and wood pitch hardened on blades slows saw and increases potential for kickback. Keep blade clean by first removing it from tool, then cleaning it with gum and pitch remover, hot water or kerosene. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause binding and KICKBACK. Use extra caution when making a "Pocket Cut" into existing walls or other blind areas. If kickback occurs, the saw could easily jump backwards over your hand, leading to serious personal injury. Fig. Forcing the saw can cause uneven cuts, loss of accuracy, and possible kickback. Push the saw forward at a speed so that the blade cuts without slowing. Use extra caution when cutting damp wood, pressure treated lumber, or wood containing knots. Adjust speed of cut to maintain smooth advancement of tool without decrease in blade speed. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. alternating current USD201-2 n . . . . . . . . . . . . . . . . . . . . no load speed ° . . . . . . . . . . . . . . . . . . . . Class II Construction . . . /min. . . . . . . . . . . . . . . . revolutions or reciprocation per minute 8 FUNCTIONAL DESCRIPTION · CAUTION: Always be sure that the tool is switched off and unplugged before adjusting or checking function on the tool. 001346 Adjusting depth of cut · CAUTION: After adjusting the depth of cut, always tighten the lever securely. 1 1. Lever Loosen the lever on the depth guide and move the base up or down. For cleaner, safer cuts, set cut depth so that no more than one blade tooth projects below workpiece. [. . . ] La Mirada, CA 90638-5753 (714) 522-8088 1970 Fulton Avenue Sacramento, CA 95825 (916) 482-5197 7674 Clairemont Mesa Blvd. 105 Van Nuys, CA 91406 (818) 782-2440 GEORGIA 4680 River Green Parkway NW Duluth, GA 30096 (770) 476-8911 NEBRASKA 4129 S. 22 - 24 Las Vegas, NV 89102 (702) 368-4277 TENNESSEE 1120 Elm Hill P. Suile 170 Nashville, TN 372 (615) 248-3321 MARYLAND 7397 Washington Boulevard, Suite 104 Elkridge, MD 21075 (410) 796-4401 NEW JERSEY 251 Herrod Blvd. [. . . ]