User manual MAKITA 4333DWD

[. . . ] Cordless Jig Saw MODEL 4331DZ MODEL 4331DWD MODEL 4333DZ MODEL 4333DWD INSTRUCTION MANUAL Model 4331D Battery Voltage 12. 0 v of stroke Length Max. cuning capacities Wood Mild Steel Aluminum ~ Strokes per minute 500-2, 800 Overall length 2~~~~ 4333D 14. 4 V "" (1") (2. 114") lo" (3/8") $ ; : ( ; ) Net weight 2. 6 kg (5. 7 Ibs) 2. 9 kg f f i 3 Ihsl Battery Cartridge 1234 IModel DC1411 High Capacity Battery Charger Voltaae 12. 0 v Voltage I I Input A. C. 7. 2 V - 14. 4 V output I Charging time 60 min. Charging time * Manufacturer reserves the right to change specifications without notice. SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE. GENERAL SAFETY RULES (For All Battery Operated Tools) WARNING! [. . . ] That wire size is at least as large as the one specified in the table below. TABLE 1 RECOMMENDED MINIMUM AWG SIZE FOR EXTENSION CORDS FOR BATTERY CHARGERS Length of Cord (Feet) AWG Size of Cord 25 18 50 18 100 18 150 16 9. IO. 11. 12. FUNCTIONAL DESCRIPTION Selecting the cutting action This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to help determine the appropriate cutting action. Position 0 Cutting action Straight linecutting action Applications For cutting mild steel, stainless steel and plastics. For clean cuts in wood and plywood. I I ~ I II I 1 ~ Small orbit cutting action Medium Orbit cutting action I I For cutting mild steel, aluminum and hard wood. For fast cutting in wood and plywood. ~ ~ ~ I I 111 Large orbit cutting action ~ ~ Installing or removing battery cartridge Always switch off the tool before insertion or removal of the battery cartridge. . To remove the battery cartridge, withdraw it from the tool while pressing the buttons on both sides of the cartridge. To insert the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. If not, it may accidentally fall out of the tool, causing injury to you or someone around you. If the cartridge does not slide in easily, it is not being inserted correctly. 8 Charging Your new battery cartridge is not charged. Use the high capacity battery charger Model DC1411 to charge the battery cart ridge. Charging light Plug the high capacity battery charger into the proper A. C. Insert the battery cartridge so that the plus and minus terminals on the battery cartridge are on the same sides as their respective markings on the high capacity battery charger. Insert the cartridge fully into the port so that it rests on the charger port floor. When the battery cartridge is inserted, the charging light color will change from green to red and charging will begin. When the charging light color changes from red to green, the charging cycle is complete. If you leave the battery cartridge in the charger after the charging cycle is complete, the charger will switch into its "trickle charge (maintenance charge)" mode which will last approximately 24 hours. After charging, unplug the charger from the power source. CAUTION: The high capacity battery charger Model DC1411 is for charging Makita battery cartridge. Never use it for other purposes or for other manufacturer's batteries. When you charge a new battery cartridge or a battery cartridge which has not been used for a long period of time, it may not accept a full charge. You can recharge the battery cartridge fully after discharging it completely and recharging a couple of times. In general, higher speeds will allow you t o cut workpieces faster but the service life of the blade will be Workpiece t o b e cut Wood M i l d steel Stainless steel Aluminum Plastics N u m b e r o n adjusting dial 3-5 3-5 3-4 2-3 1-4 CAUTION: Adjust the speed adjusting dial only within the range of numbers 1 through 5. [. . . ] The use of any other accessories or attachments might present a risk of injury to persons. The accessories or attachments should be used only in the proper and intended manner. An exception: Universal shank jig saw blades with a thickness of 1 m m - 1. 25 m m (1/32" - 3/64") and a length of 58 m m - 82 m m (2-9/32" - 3-7/32"). Plastic base plate Part No. 415524-7 High Capacity Battery Charger Model DC1411 Hex wrench 3 Part No. [. . . ]