User manual MAKITA 3704

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual MAKITA 3704. We hope that this MAKITA 3704 user guide will be useful to you.


MAKITA 3704 : Download the complete user guide (486 Ko)

You may also download the following manuals related to this product:

   MAKITA 3704 (487 ko)
   MAKITA 3704 (487 ko)
   MAKITA 3704 (487 ko)
   MAKITA 3704 (487 ko)
   MAKITA 3704 ANNEXE 764 (371 ko)
   MAKITA 3704 ANNEXE 554 (371 ko)

Manual abstract: user guide MAKITA 3704

Detailed instructions for use are in the User's Guide.

[. . . ] They are double-insulated in accordance with European Standard and can, therefore, also be used from sockets without earth wire. Safety hints For your own safety, please refer to the enclosed safety instructions. Hold tool by insulated gripping surfaces when performing an operation where the cutting tools may contact hidden wiring or its own cord. Contact with a ``live'' wire will make exposed metal parts of the tool ``live'' and shock the operator. [. . . ] nOTE: · Moving the tool forward too fast may cause a poor quality of cut, or damage to the bit or motor. The proper feed rate will depend on the bit size, the kind of workpiece and depth of cut. Before beginning the cut on the actual workpiece, it is advisable to make a sample cut on a piece of scrap lumber. This will show exactly how the cut will look as well as enable you to check dimensions. ⷠWhen using the trimmer shoe, the straight guide or the trimmer guide, be sure to keep it on the right side in the feed direction. CAUTION: Since excessive cutting may cause overload of the motor or difficulty in controlling the tool, the depth of cut should not be more than 3 mm at a pass when cutting grooves. When you wish to cut grooves more than 3 mm deep, make several passes with progressively deeper bit settings. Use the bolts, wing nuts, spring washers and flat washers to install the trimmer shoe as shown in Fig. To adjust the bit protrusion, loosen the nut and move the tool base up or down as desired by turning the adjusting screw. The straight guide is effectively used for straight cuts when chamfering or grooving. Attach the guide plate to the straight guide with the bolt, the wave washer, the flat washer and the wing nut. Loosen the wing nut on the straight guide and adjust the distance between the bit and the straight guide. When cutting, move the tool with the straight guide flush with the side of the workpiece. If the distance (A) between the side of the workpiece and the cutting position is too wide for the straight guide, or if the side of the workpiece is not straight, the straight guide cannot be used. In this case, firmly clamp a straight board to the workpiece and use it as a guide against the trimmer base. CAUTION: With the tool unplugged and switch in the ``OFF'' position, rotate the collet nut on the tool several times to be sure that the bit turns freely and does not contact the base or trimmer shoe in any way. Turn the tool on without the bit making any contact with the workpiece and wait until the bit attains full speed. Then move the tool over the workpiece surface, keeping the tool base and trimmer shoe flush with the sides of the workpiece. [. . . ] Place the tool on the templet and move the tool with the templet guide sliding along the side of the templet. NOTE: The workpiece will be cut a slightly different size from the templet. Allow for the distance (X) between the router bit and the outside of the templet guide. The distance (X) can be calculated by using the following equation: Distance (X) = outside diameter of the templet guide ­ router bit diameter 2 CAUTION: Always be sure that the tool is switched off and unplugged before carrying out any work on the tool. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE MAKITA 3704




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual MAKITA 3704 will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.