User manual MAKITA 2106

[. . . ] When not in use, before servicing, and when changing accessories, such as blades, bits, cutters. 2 14. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. Make sure your extension cord is in good condition. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. A n undersized cord will cause a drop in line voltage resulting in loss of power and overheating. [. . . ] To stop the tool from the locked position, pull the trigger fully, then release it. I Lock button Trigger switch 1 1 1 CAUTION : Before plugging in the tool, always check to see that the trigger switch actuates properly and returns to the "OFF" position when released. Speed change To change the tool speed, press the "H" side of the speed change switch for high speed or the "L" side for low speed. CAUTION : Do not change the tool speed while the motor is running. 5 Installing or removing blade CAUTION : Always be sure that the tool is switched off and unplugged before installing or removing the blade. Oil on the blade can cause the blade to slip or come off unexpectedly. 0 Use caution when handling the blades so that you are not cut by their sharp teeth Turn the blade tightening lever clockwise until it hits against the protrusion on the frame. Match the direction of the arrow on the blade to that of the arrow on the wheels. v Blade tightening lever Insert the blade between the bearings of one blade guide first and then into the other blade guide. The blade back should contact the bearings in the lower portion of the blade guides. Bearing , , r\-\ Blade Blade guide I 6 Position the blade around the wheels and insert the other side of the blade within the Blade guide I -T- Hold the blade in place and turn the blade tightening lever counterclockwise until it hits against the protrusion on the frame. Make sure that the blade is correctly positioned within the blade guard and around the wheels. Start and stop the tool two or three times to make sure that the blade runs properly on the wheels. CAUTION : While making sure that the blade runs on the wheels properly, keep your body away from the blade area. CAUTION : When turning the blade tightening lever clockwise to release the tension on the blade, the blade may come off unexpectedly. Installing stopper plate (For Model 2106 only) This tool i s shipped from the factory without the stopper plate installed. Install the stopper plate on the frame so that the blade can run through the slot in the stopper plate. While pressingthe stopper plate against the frame, secure the stopper plate with the bolts using the hex wrench. 7 Squaring blade with stopper plate Use the triangular rule to make sure that the side of the blade i s square with the side of the stopper plate. If not square, loosen the bolts securing the stopper plate and adjust the stopper plate accordingly. Triangular rule Cutting lubricant When cutting metals, use Makita cutting wax as a cutting lubricant. To apply the cutting wax to the blade teeth, start the tool and cut in to the cutting wax as shown in the figure. 0 CAUTION : Never use cutting oil or apply excessive amount of wax to the blade. 0 When cutting cast iron, do not use any cutting lubricant. Cutting operation It i s important to keep a t least two teeth in the cut. Select the proper cutting position for your workpiece by refering to the figure a t right. , o , x , 8 Hold the tool as shown in the figure with the stopper plate contacting the workpiece and the blade clear of the workpiece. Turn the tool on and wait until the blade attains full speed. The weight of the tool or slightly pressing the tool down will supply adequate pressure for the cutting. As you reach the end of a cut, release pressure and, without actually raising the tool, lift it slightly so that it will not fall against the workpiece. CAUTION : Applying excessive pressure to the tool or twisting of the blade may cause bevel cutting or damage to the blade. 0 When not using the tool for a long period of time, remove the blade from the tool. 0 9 MA1NTENANCE CAUTION : Always be sure that the tool i s switched off and unplugged before attempting to perform inspection or maintenance. [. . . ] It is warranted t o be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, retum the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. If inspection shows the trouble is caused by defective workmanship or material, Makita will repair (or at our option, replace) without charge. This Warranty does not apply where: repairs have been made or attempted by others: 0 repairs are required because of normal w a and tear: er The tool has been abused, misused or improperly maintained; alterations have been made to the tool. IN NO EVENT SHALL MAKITA BE LIABLE FOR ANY INDIRECT, INCIDENTAL OR CONSEQUENTIAL DAMAGES FROM THE SALE OR USE OF THE PRODUCT. [. . . ]