User manual MAKITA 1002 BA

[. . . ] Inspect tool cords periodically and if damaged, have repaired by authorized service facility. changing accessories, such as blades, bits, cutters. - - L 14. Form habit of checking t o see that keys and adjusting wrenches are removed from tool before turning it on. When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. [. . . ] When using an extension cord, be sure t o use one heavy enough t o carry the current your product will draw. An undersized cord will cause a drop in line voltage resulting in loss of power and overheating. Table 1 shows the correct size t o use depending on cord length and nameplate ampere rating. MINIMUM GAGE FOR CORD SETS Total Length of Cord in Feet 0-25 I 25-50 I 51-100 I 101-150 Ampere Rating More Not More AWG Than Than 18 16 0 6 16 14 6 10 18 16 14 12 16 16 14 12 10 12 12 16 14 12 Not Recommended - 17. When tool is used outdoors, use only extension cords intended for use outdoors and so marked. Before further use of the tool, a guard or other part that is damaged should be carefully checked t o determine that it will operate properly and perform its intended function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting, and any other conditions that may affect its operation. A guard or other part that is damaged should be properly repaired or replaced by an authorized service center unless otherwise indicated elsewhere in this instruction manual. To reduce the risk of electric shock, this equipment has a polarized plug (one blade is wider than the other). H it still does not fit, contact a qualified electrician t o install the proper outlet. For continuous operation, pull the trigger and then push in the lock button. To stop the tool from the locked position, pull the trigger fully, then release it. CAUTION: Before plugging in the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. 6 Sharpening planer blades Always keep your blades sharp for the best performance possible. Use the sharpening holder to remove nicks and produce a fine edge. Sharpening holder First, loosen the two wing nuts on the holder and insert the blades (A) and (B), so that they contact the sides (C) and (D). Then tighten the wing nuts. Wing nut Side (C) Blade (A) Blade (6) Immerse the dressing stone in water for 2 or 3 minutes before sharpening. Hold the holder so that the blades both contact the dressing stone for simultaneous sharpening at the same angle. MAINTENANCE CAUTl ON : Always be sure that the tool is switched off and unplugged before attempting to perform inspection or maintenance. Replacing carbon brushes Remove and check the carbon brushes regularly. Use only identical carbon brushes. I Use a screwdriver to remove the chip cover. Limit mark 1 Use a screwdriver to remove the brush holder caps. Take out the worn carbon brushes, insert the new ones and secure the brush holder caps. // Sdrewdriver Chipcover I Brush holder cap \ To maintain product SAFETY and RELIABILITY, repairs, any other maintenance or adjustment should be performed by Makita Authorized or Factory Service Centers, always using Makita replacement parts. 8 ACCESSORIES CAUTION These accessories or attachments are recommended for use with your Makita tool specified in this manual The use of any other accessories or attachments might present a risk of injury to persons The accessories or attachments should be used only in the proper and intended manner Planer blade Width 110 mm (4-3/8") Part No 793008-8 Planer blade (Material Tungsten-carbide) Width 110 m m (4-3/8") Part No 7930096 Sharpening holder assembly Part No. 123062-2 9 Seo. -ll-'97 US 110 mm (4-318") CURVED PLANER Model 1002 BA e Note: The switch and other part configurations may differ from country to country. 10 MODEL 1002 BA Sep. -11-'97 DESCRIPTION O "' ;M US , &, MACHINE ___ 1 2 3 4 5 6 1 1 1 2 2 2 ED DESCRIPTION 1 1 1 1 1 1 1 Belt cover Ball Bearing 6200LB Insulation Washer ARMATURE ASSEMBLY (With Item 34. 35, 36 & 39) Flat Washer 12 Ball Bearing 6ZOlDDW Rubber Pin 6 Pan Head Screw M5x65 Rubber Pin 4 FIELD ASSEMBLY Hex Flange Head Bolt M6x17 Drum Plate Pan Head Screw M4x5 Adjusting Plate Planer Blade 1 1 0 Rubber Pm 6 Ball Bearing 620122 Washer 12 Drum Washer 10 Ball Bearing 620022 Rubber Pin 4 Front Base Rubber Packmg Compression Spring 21 Front Box Flat Washer 13 Knob 6 4 Label MACHINE ~ 7 6 2 2 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 21 28 29 4 1 1 1 1 1 2 1 3 1 6 2 1 1 2 1 1 1 2 2 1 2 1 30 31 32 Pan Head Screw M4x50 Pan Head Screw M4x20 Chtp Cover Brush Holder Cap Carbon Brush Wing Bolt M6x25 Spring Washer 6 Flat Washer 6 Rivet 0 - 5 Name Plate Main Frame Cord Cord Guard Strain Relief Pan Head Screw M4x18 Handle Cover Pan Head Screw M4x30 Bracket [With Item 40 & 491 Pan Head Screw M5x28 Pan Head Screw M4x30 Poly V Belt 6 - 2 1 2 V Pulley 6 - 2 3 L Pan Head Screw M 4 x 6 Switch Pan Head Screw M4x12 Fan Guide Pin 6 Pan Head Screw M5x28 Base Pan Head Screw M5x18 V Pullev 6 - 30 33 34 35 36 38 39 40 41 42 43 44 45 46 41 48 49 50 51 52 53 54 55 56 51 58 59 2 1 1 8 2 4 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 60 61 62 Note The switch and other part specifIcattonS may dlffer from country t o country 11 i MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. [. . . ] 123062-2 9 Seo. -ll-'97 US 110 mm (4-318") CURVED PLANER Model 1002 BA e Note: The switch and other part configurations may differ from country to country. 10 MODEL 1002 BA Sep. -11-'97 DESCRIPTION O "' ;M US , &, MACHINE ___ 1 2 3 4 5 6 1 1 1 2 2 2 ED DESCRIPTION 1 1 1 1 1 1 1 Belt cover Ball Bearing 6200LB Insulation Washer ARMATURE ASSEMBLY (With Item 34. 35, 36 & 39) Flat Washer 12 Ball Bearing 6ZOlDDW Rubber Pin 6 Pan Head Screw M5x65 Rubber Pin 4 FIELD ASSEMBLY Hex Flange Head Bolt M6x17 Drum Plate Pan Head Screw M4x5 Adjusting Plate Planer Blade 1 1 0 Rubber Pm 6 Ball Bearing 620122 Washer 12 Drum Washer 10 Ball Bearing 620022 Rubber Pin 4 Front Base Rubber Packmg Compression Spring 21 Front Box Flat Washer 13 Knob 6 4 Label MACHINE ~ 7 6 2 2 9 10 11 12 13 14 15 17 18 19 20 21 22 23 24 25 26 21 28 29 4 1 1 1 1 1 2 1 3 1 6 2 1 1 2 1 1 1 2 2 1 2 1 30 31 32 Pan Head Screw M4x50 Pan Head Screw M4x20 Chtp Cover Brush Holder Cap Carbon Brush Wing Bolt M6x25 Spring Washer 6 Flat Washer 6 Rivet 0 - 5 Name Plate Main Frame Cord Cord Guard Strain Relief Pan Head Screw M4x18 Handle Cover Pan Head Screw M4x30 Bracket [With Item 40 & 491 Pan Head Screw M5x28 Pan Head Screw M4x30 Poly V Belt 6 - 2 1 2 V Pulley 6 - 2 3 L Pan Head Screw M 4 x 6 Switch Pan Head Screw M4x12 Fan Guide Pin 6 Pan Head Screw M5x28 Base Pan Head Screw M5x18 V Pullev 6 - 30 33 34 35 36 38 39 40 41 42 43 44 45 46 41 48 49 50 51 52 53 54 55 56 51 58 59 2 1 1 8 2 4 2 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 60 61 62 Note The switch and other part specifIcattonS may dlffer from country t o country 11 i MAKITA LIMITEDONE YEAR WARRANTY Warranty Policy Every Makita tool is thoroughly inspected and tested before leaving the factory. It is warranted to be free of defects from workmanship and materials for the period of ONE YEAR from the date of original purchase. Should any trouble develop during this one-year period, return the COMPLETE tool, freight prepaid, to one of Makita's Factory or Authorized Service Centers. [. . . ]