User manual MAGELLAN NAV 6510

[. . . ] MAGELLAN NAV 6500/NAV 6510 User Manual © 1998 by Magellan Corporation. No part of this User Guide may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, for any purpose other than the purchaser's personal use without the written permission of Magellan Corporation. MagellanTM, GPS NAV 6500/ NAV 6510TM are the trademarks of Magellan Corporation. 630323 Magellan NAV 6500/ NAV 6510 User Manual WARNINGS USE GOOD JUDGEMENT This product is an excellent navigation aid, but does not replace the need for careful orienteering and good judgement. [. . . ] Default setting: MMM-DD-YY. Turning the Beeper On or Off Time can be shown as 24 hours or 12 hours (AM/PM). Press the Aux softkey, highlight General Setup using the CURSOR KEY, and press ENTER. Highlight Time Format and press ENTER to display a window 24 hour 12 hour with the options 24, 12. Default setting: 24 hour Setting Date Format The beeper can be turned on and off. Press the Aux softkey, highlight General Setup using the CURSOR KEY and press ENTER. High- OFF ON light Beeper, press ENTER and a window opens shows On/Off. Default setting: On Language Setting Date can be shown as Month-Day-Year or Day-Month-Year. Press the Aux softkey, highlight General Setup using CURSOR KEY, and press ENTER. Highlight Date Format, press ENTER and a window opens that lists MMM-DD-YY and DD-MMM-YY. MMM-DD-YY DD-MMM-YY The receiver supports five languages: English, Italian, French, German and Spanish. Press the Aux softkey, highlight General Setup using the CURSOR KEY and press ENTER. Highlight Language, press ENTER and a window opens listing the languages. 40 Magellan NAV 6500/NAV 6510 Use the CURSOR KEY to select one and press ENTER. Default setting: English Navigation Setup English Italiano Francais Deutsch Espanol The important difference between Deg/Min/Sec and Deg/Min/Fractions is that there are 60 seconds in one minute of latitude or longitude (the seconds value will always be between 00 and 59), whereas fractions of a minute are expressed in decimal format (from . 00 to . 99, or . 000 to . 999). Press the Aux softkey, use the CURSOR KEY to highlight Navigation Setup, and press ENTER. Use the CURSOR KEY to highlight Coordinate System, and press ENTER. ddd mm. ss ddd mm. mm ddd mm. mmm UTM OSGB TD The Navigation Setup menu enables you to change the coordinate system, map datum, north reference, map orientation, and NAV 2 screen setup. It also activates or deactivates course projection. Coordinate System Map Datum North Reference Map Orientation Projected Course Nav2 Screen Setup SOG COG DTG CTS XTE STR ddd mm. mm WGS 1984 Auto Mag. North Up OFF Use the CURSOR KEY to highlight desired coordinate system and ENTER to set. The ASF value can be set to correct the coordinates in case of map shift 0. 0 to 9. 9. TD Settings Chain: Pair: ASF 1: ASF 2: Prime: 9970 XY +0. 0 +0. 0 ON Selecting Coordinate System Position coordinates displayed on the NAV1 screen and waypoint coordinates displayed on the waypoint screen can be based on latitude/longitude, Universal Transverse Mercator (UTM), Ordinance Survey of Great Britain (OSBG) or Loran TD's. If latitude/longitude is selected, the position can be displayed in Degrees, Minutes, Seconds or Degrees, Minutes and fractions of minutes to 2 or 3 digits of resolution, (ddd mm. mm or ddd mm. mmm). Magellan NAV 6500/NAV 6510 Turn Prime OFF if the coordinate position does not correspond to the chart position. (Since two solutions are possible, mathematically, in certain rare cases the second calculation is the more accurate of the two. ) Press ESC to exit. Default setting: latitude/longitude, ddd mm. mm tions of mins to 2 places resolution) (Frac41 Selecting Map Datum The receiver allows selecting from 93 different map datums. Only position coordinates displayed on the NAV1 screen and waypoint coordinates entered manually (not through the map) are based on the map datum selected by the user through the Aux function. Press the Aux softkey, use the CURSOR KEY to highlight Navigation Setup and press ENTER. [. . . ] Map makers may use a different model to chart their maps from so positions will differ from one datum to another. The datum for the map you are using can be found in the legend of the map. Coordinates Course CTS Estimated Estimated Position Error is the approximate Position Error error (between 0 and X) introduced in the (EPE) ephemeris by the U. S. This random error, known as Selective Availability (SA) is not due to receiver error and is not significant enough to affect navigation for most purposes (See DGPS in appendix). Geometric Quality (HDOP) GOTO Measures the probable accuracy of a position fix, based on the position of the satellites relative to each other. [. . . ]