User manual MACKIE D2

[. . . ] 2-Channel DJ Mixer with FireWire Option OWNER'S MANUAL MIC OL SIG +3 +50 48V OFF ON O O PGM U 1 PGM SOURCE LINE/ PHONO 2 U CONTROL MAIN SOURCE LINE/ PHONO MAX CD CD O O MAX O O MAX LEVEL LEVEL LEVEL LEVEL EQ U EQ HIGH KILL +10 EQ HIGH KILL +10 BOOTH STEREO MONO U HIGH -15 +15 O O MAX LEVEL FX U MID -15 +15 MID KILL +10 KILL +10 MID O O +15 SEND U LOW -15 +15 LOW KILL +10 KILL +10 LOW O O +15 RETURN PHONES PGM MAIN U ON FX FX O O MAX LEVEL PGM SOURCE PAN BAL BAL 1 2 L R LR LR PGM 1 PGM 2 TRANSFORM TRANSFORM MAIN L OL 10 7 4 2 0 2 4 7 10 20 30 REVERSE OL 10 7 4 2 0 2 4 7 10 20 30 REVERSE R OL 10 7 4 2 0 2 4 7 10 20 30 REVERSE infinium contact-free cross-fader A B d. 2 2-channel DJ Mixer Important Safety Instructions 1. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. [. . . ] MID EQ This knob gives you up to 10 dB of boost at 1 kHz, and turns off the signal at 1 kHz when the knob is turned to the KILL position. At the center position, the MID EQ has no effect on the signal. 29. LOW EQ This knob gives you up to 10 dB of boost at 300 Hz and below, and turns off the signal at 300 Hz and below when the knob is turned to the KILL position. Note: When all three EQ knobs are turned to the KILL position, the signal is effectively muted and no signal passes through to the output. Owner's Manual 13 d. 2 2-channel DJ Mixer Control Section 32. MAIN LEVEL Control MIC PGM U 48V OFF ON O O 1 PGM SOURCE LINE/ PHONO 2 U CONTROL MAIN This knob adjusts the main output level at the MAIN OUT XLRs [9] (and to the RCA Main Outs [11] when the LIVE/RECORD switch [12] is out). (Remember, when the LIVE RECORD switch is pushed in, the RCA Main Outs are not affected by the MAIN LEVEL control. ) OL SIG +3 +50 SOURCE LINE/ PHONO MAX CD CD O O MAX O O MAX LEVEL LEVEL LEVEL LEVEL EQ U EQ HIGH KILL +10 EQ HIGH KILL +10 BOOTH STEREO MONO U HIGH -15 +15 O O MAX LEVEL FX U MID -15 +15 MID KILL +10 KILL +10 MID O O +15 SEND U LOW -15 +15 LOW KILL +10 KILL +10 LOW O O +15 RETURN PHONES PGM MAIN U ON FX FX O O MAX LEVEL PGM SOURCE 33. BOOTH LEVEL Control This knob adjusts the output level at the BOOTH outputs [8]. PAN BAL BAL 1 2 L R LR LR 37. PHONES LEVEL Control This controls the volume of the PHONES output from off to maximum gain. STEREO/MONO Switch With this switch up, the BOOTH outputs [8] provide a stereo left and right output of the main mix. Push the switch in to combine the left and right signals to mono if you only have one booth monitor speaker. 38. PGM/MAIN Switch Use this switch to select the source for the headphones signal. When the switch is up (PGM position), the signal is tapped just after the BAL control [30] on the PGM channels. You can use the PGM SOURCE crossfader [39] to fade between PGM 1 and PGM 2. When the switch is down (MAIN position), the signal is tapped from the Main Mix bus, just before the MAIN LEVEL control [32]. 35. FX SEND LEVEL Control This knob controls the amount of signal being sent to FX SEND outputs [6]. Adjust this knob to provide an appropriate input signal level to your external effects processor (or whatever you have connected to the FX SENDs). Note: The FX SENDs are affected by the TRANSFORM switches [40], so if you mute a PGM channel with the TRANSFORM switch, the FX SEND for that PGM channel is muted as well. 39. PGM SOURCE Cue Crossfader When the PGM/MAIN switch [38] is up (in the PGM position), you can use this crossfader to listen to PGM 1 and PGM 2 in the headphones. When the crossfader is all the way to the left, PGM 1 is heard in the headphones. When the crossfader is all the way to the right, PGM 2 is heard in the headphones. When the knob is in the center, the headphones get an even mix of PGM 1 and 2. Note: When the PGM/MAIN switch is down (MAIN position), this control has no effect on the PHONES output. 36. [. . . ] Ship the product in its original shipping carton, freight prepaid to the authorized service center. The address of your closest authorized service center will be given to you by Technical Support. IMPORTANT: Make sure that the Service Request Number is plainly written on the shipping carton. LOUD Technologies reserves the right to inspect any products that may be the subject of any warranty claims before repair or replacement is carried out. [. . . ]