User manual MACKIE ART500A DATASHEET

[. . . ] ART Series Careful acoustic design and advanced materials have resulted in an exceptional full range, full fidelity, self-contained sound system. The ART500A provides an ideal combination of high power, low distortion and wide bandwidth for permanent installations. [. . . ] (35mm) lockable stand mount 1 Measured on axis in the far field, referenced back to 1 watt RMS from maximum power and to 1 meter distance using the inverse square law. 2 RMS using 20Hz to 20kHz, PN Spectrum, Peak for 2 hours with +6 dB crest factor. 2 OF 6 PAGES ART500A Two-Way Active Speaker System ART500A Vertical Polars 200Hz 0° 250Hz 315Hz 400Hz 0° 500Hz 630Hz 800Hz 1kHz 0° 1. 25kHz 0° 1. 6kHz 2kHz 2. 5kHz 3. 15kHz 4kHz 5kHz 6. 3kHz Vertical Off-Axis Frequency Response (UP) 8kHz 0° 10kHz 12. 5kHz 16kHz Vertical Off-Axis Frequency Response (DOWN) 3 OF 6 PAGES ART500A Two-Way Active Speaker System ART500A Horizontal Polars 0° 0° 200Hz 250Hz 315Hz 400Hz 500Hz 630Hz 800Hz 1kHz 0° 0° 1. 25kHz 1. 6kHz 2kHz 2. 5kHz 3. 15kHz 4kHz 5kHz 6. 3kHz Horizontal Off-Axis Frequency Response 0° 8kHz 10kHz 12. 5kHz 16kHz 4 OF 6 PAGES ART500A Two-Way Active Speaker System Frequency response is measured on-axis at a distance referenced back to 1m at 1-watt drive. Frequency Directivity Index 10. 47" (266mm) 5. 35" 5. 11" (130mm) (136mm) 11. 85" (301mm) 15. 74" (400mm) 8. 26" (210mm) 8. 11" (206mm) 10. 47" (266mm) 17. 28" (439mm) 14. 77" (375mm) BOTTOM SIDE 17. 88" (454mm) 8. 26" (210mm) CONCEIVED, DESIGNED, AND MANUFACTURED BY MACKIE INDUSTRIAL · MADE IN ITALY · COPYRIGHT ©1999 INPUT OUTPUT LINE/MIC VOICE MUSIC LIMIT. OPERATE VOLUME 20. 35" (517mm) 25. 31" (643mm) LINE 120 VAC/240 VAC 50­60Hz FUSE T14A 240V ­ T7. 5A 120V PMAX 600W MIC LINE THE FOLLOWING ARE TRADEMARKS REGISTERED TRADEMARKS OF MACKIE DESIGN INC. : "MACKIE" "MACKIE INDUSTRIAL" & THE "RUNNING MAN" FIGURE , , OFF ON OFF ON SERIAL NUMBER MANUFACTURING DATE 29. 15" (740mm) AC OUTLET 120V/240V 5A MAX POWER SERIAL NUMBER MANUFACTURING DATE 11. 96" (304mm) THIS APPARATUS MUST BE GROUNDED FRONT REAR 5 OF 6 PAGES ART500A SPEAKER ART500A Two-Way Active Speaker System Architects' & Engineers' Specifications The amplified loudspeaker system shall be a selfcontained unit, housed in a reinforced polypropylene enclosure and consisting of the following sub-systems: (1) vented two-way loudspeaker system, (2) integrated power amplifiers and crossover network, (3) integrated mic/line input with music and voice equalizers. The loudspeakers shall consist of a 15 inch lowfrequency, cone driver, with at least a 3 inch voice coil, and an 80° x 60° high-frequency, constantdirectivity polynomial horn with a horn-loaded, 2 inch compression driver having a titanium diaphragm and compensated for horn resonance and ringing. The drivers shall be aligned with an analog circuit and crossed over at 1. 2kHz by a 4-pole network built into the power amplifiers. Two discrete amplifiers shall be provided, capable of continuously delivering 400W RMS to the low-frequency driver and 100W RMS to the highfrequency driver. They shall be equipped with a multi-function protection circuit to peak limit and protect the loudspeakers from overheating, over-excursion, overloads, short circuits and extreme operating temperatures. An indicator light shall illuminate when any aspect of the protection circuit engages. The integrated mic/line input shall be actively balanced, may also accept an unbalanced input, and shall be paralleled to an output. The input shall have a switch to select between 10mV mic and 775mV line levels. The unit shall be provided with both voice and music optimization equalization that can be activated with buttons on the rear panel. A continuously variable, rotary master volume control shall be provided. The power supply shall be internal and connected to 50 or 60Hz source current through a detachable IEC power cord and shall have an IEC socket for mains power loop-through. [. . . ] For this reason, any current Mackie Industrial product may differ in some respect from its published description, but will always equal or exceed the original design specifications unless otherwise stated. 910-166-10 www. mackieindustrial. com 16220 Wood-Red Rd NE, Woodinville, WA 98072 USA 888. 337. 7404, fax 425. 487. 4337, industrial@mackie. com UK + 44 1268 570 808, fax + 44 1268 570 809, industrial@rcf-uk. com ITALY +39 0522 354 111, fax +39 0522 332 294, industrial@rcf. it FRANCE +33 3 8546 9160, fax +33 3 8546 9161, industrial@rcf. fr GERMANY +49 2572 96042 0, fax +49 2572 96042 10, industrial@mackie. de 6 6 OF 6 PAGES [. . . ]