User manual M-TECH SX 35 DSC

[. . . ] SX 35 DSC SELECT VOL DISTRESS SQ MENU EXIT HI/LO SCAN END MEM 16 CALL SX 35 DSC ENT LIFT HERE OFF OWNER'S HANDBOOK Declaration of Conformity I hereby declare that the product Maritime transceiver : M-TECH SX 35 DSC (Name of product, type or model, batch or serial number) satisfies all the technical regulations applicable to the product within the scope of Council Directives 73/23/EEC, 89/336/EEC and 99/5/EC : EN 60945:1997 ETSI EN 301 843-1, -2 V1. 1. 1: 2001-02 ETSI EN 301 025-1: V1. 1. 2: 2000-08 ETSI EN 301 025-2 : V1. 1. 1: 2000-08 ETSI EN 301 025-3: V1. 1. 1: 2001-05 (Title(s) of regulations, standards, etc. ) All essential radio test suites have been carried out. Rasek - Address : Boelwiese 5, 91320 Ebermannstadt, Germany Identification Number : 0678 MANUFACTURER or AUTHORISED REPRESENTATIVE : - Address : Pony Electric Corporation No. This declaration is issued under the sole responsiblility of the manufacturer and, if applicable, his authorised representative. - Point of contact : Tadashi Watanabe (Tel : +81-3-3405-5733 Fax : +81-3-3405-8677) (Name, telephone and fax number) Tokyo Japan 2002-03-11 (Place, date of issue) (Signature) Tadashi Watanabe, President (Name and title in block letters) SX 35 DSC 1 NOTICE This device is only and aid to navigation. [. . . ] Entries to the list can be added or edited as necessary to keep your directory current. To add a name and MMSID to the directory: · · Press the MENU key. If the directory is empty, the screen appears blank except for the channel number. If no empty line is found, the directory is full and a previous entry must be overwritten. The DIRECTORY NAME/ID screen appears with a 22 SX 35 DSC blinking cursor next to the name line. DIRECTORY NAME/ID ³ INT Name and ID Screen · Press the name line. SPECIAL NOTE Characters are entered in the name and ID fields using either the SELECT knob or the microphone keys. All letters in the alphabet, a space, and the numbers 0~9, plus punctuation marks and some symbols may be used. The space character follows Z in the alphabet when using the SELECT knob. The following table shows the characters that may be entered in the name field using the microphone keys. M ic r o p h o n e K e y s GHI JKL MNO 4 5 6 ENT or ENT key to move the cursor to the first character of the 0 0 Space ( ) % 1 1 , . / ABC 2 DEF 3 PQRS 7 TUV 8 T U V & 8 W XYZ 9 W X Y Z 9 A lp h a n u m e r ic C h a r a c te r S e q u e n c e A D G J M P B E H K N Q C F I L O R ?: # ' S 2 3 4 5 6 7 Several additional special characters are available when entering the name using the SELECT knob. · · Use the SELECT knob or microphone keys to select the desired letter, number or symbol for the first character. If using the SELECT knob, press the ENT or ENT key after each charac- SX 35 DSC 23 ter is selected to enter the character and advance the cursor to the next character position. · If using the microphone keys, press the appropriate key repeatedly until the desired character is displayed at the cursor position. When entering the same character in two or more successive character positions, use the cursor. · · · Use the EXIT ENT or ENT keys to advance the key if necessary to backspace the cursor. Up to ten characters are allowed in the name, but only one is required. After the last character in the name is selected and entered, press the ENT or ENT key again. or ENT · · · · Press the ENT key to move the cursor to the first digit position in the MMSID line. Press the next microphone number key or press the ENT key to store the selected digit and move the cursor to the next digit position. Continue to select and store digits until the complete MMSID is entered. After the last MMSID digit is entered, the cursor returns to the name line of the display. If the name and ID are correct for this directory entry, press the MENU key to save the data and exit. [. . . ] ee 48 SX 35 DSC Specifications SX DSC 35 Technical Specifications GENERAL Compliance: Meets EU specification EN301-025 V1. 1. 2 (August 2000), Radio Regulations Appendix 18, and DSC Class D/SC-101. -20 Degrees C to +50 Degrees C UV Stable Case with Tactile-Feel colored silicon rubber key switches Backlighted rubber keypad. 4 Lines with 11 characters each and BOLD channel number display with 3 discrete annunciators. Silver background with dark Black letters and Bright Orange display backlighting. [. . . ]