User manual M-AUDIO STUDIOPHILE BX5A DELUXE

[. . . ] Woofer The woofer unit is 5 inches in diameter with a magnetically shielded Kevlar cone, high-temperature voice coil and damped rubber surround. M-Audio's new BX5a Deluxe employs Kevlar for low-frequency driver construction. The same material used in bullet-proof vests, Kevlar's high resilience makes it ideal for use in speaker cones--although it is typically reserved for monitors with higher price tags than the BX5a Deluxe. Needless to say, Kevlar represents a significant improvement over the polypropylene and paper used in most monitors at this price. 2. [. . . ] TRS INPUT: This jack accepts 1/4" connections with either balanced or unbalanced wiring. The input wiring of a TRS connector should be as follows: 2 <TRS TIP . signal ground (shield) Studiophile BX5a Deluxe Unbalanced 1/4" wiring can be done with either a two- or three-conductor (TS or TRS) plug. A two-conductor (TS) plug automatically grounds the signal negative input, whereas a three-conductor (TRS) plug, wired unbalanced, provides the option of leaving the negative input open or grounded. We recommend that you ground the unused negative input (this can be done by wiring the ring and sleeve of the TRS plug together). The TRS input is summed through a balanced input amplifier with the XLR input, allowing both inputs to be used simultaneously. PRODUCT SPECIFICATION: This label contains the model and specification information. SUB-FREQUENCY VENT PORT: This port aids in reproduction of very low frequencies by discharging frequencies below 60Hz. VOLUME CONTROL: Use the volume control to set the output sound pressure from the BX5a Deluxe to proper levels as required. POWER RECEPTACLE: Accepts a detachable 3-circuit line cord in order to power the monitor. VOLTAGE-SELECT SWITCH: Provides two selections, 115V AC and 230V AC, and should be set to match the "house supply" (receptacle) voltage of the country or location in which the speaker is used. The 115V setting is correct for the USA, while the 230V setting is correct for most of the UK and Europe. POWER SWITCH: This switch turns the monitor on and off. Front Panel Features The front panel houses the Power LED, which indicates whether the speakers (amplifier) power is on or off. Power LED HF Driver (Tweeter) LF Driver (Woofer) 6. 5" (176 mm) 8. 75" (200 mm) 3 English 9. 87" (250 mm) Installation For optimal performance of the BX5a Deluxe, please read the following thoroughly and carefully prior to installation. Precautions Handling: Please do not touch the speaker cones. The BX5a set is packaged in the box tightly, so your attention is required when taking the monitors out of the box. To avoid possible damage to the speaker units, hold both sides of the monitor in order to pull it out of the box. The speaker cones should not be touched in order to avoid damage even after they are out of the box. Correct Power Operation: Since the BX5a Deluxe contains its own amplifier, it must be connected to a power outlet using the detachable AC cable provided. Before connecting power, please make sure that the Voltage-Select Switch located on the speaker's rear panel is set to the appropriate position, as described in the rear-panel features list appearing earlier in this manual. - Use of improper Voltage-Select Switch combinations may result in hazardous conditions and/or damage to speaker components not covered by speaker warranty. Connections: You can connect either an XLR balanced cable or TRS balanced/unbalanced cable from the input of each BX5a to your corresponding preamp, computer or game console outputs. [. . . ] PLACE THOSE MATERIALS AWAY FROM THE PATH OF THE SOUND FROM THE BX5a's. Warranty Warranty Terms M-Audio warrants products to be free from defects in materials and workmanship, under normal use and provided that the product is owned by the original, registered user. Visit www. m-audio. com/warranty for terms and limitations applying to your specific product. Warranty Registration Immediately registering your new M-Audio product entitles you to full warranty coverage and helps M-Audio develop and manufacture the finest quality products available. Register online at www. m-audio. com/register to receive FREE product updates and for the chance to win M-Audio giveaways. Appendix A - Technical Specifications Type: LF Driver: HF Driver: Frequency Response: Crossover Frequency: LF Amplifier Power: HF Amplifier Power: S/N Ratio: Input Connectors: Polarity: Input Impedance: Input Sensitivity: Protection: Indicator: Power Requirements: Cabinet: Dimension: Weight: 2-way near-field studio reference monitors 5-inch Kevlar curved cone with high temperature voice coil and damped rubber surround. 1-inch magnetically shielded natural silk dome 56Hz - 22kHz 3kHz 40W 30W > 100dB typical A-weighted 1 x XLR balanced input connector 1 x TRS balanced/unbalanced input connector positive signal at + input produce outward LF cone displacement 20k ohms balanced, 10k ohms unbalanced 85mV pink noise input produces 90dBA output SPL at one meter with volume control at maximum RF interference, output current limiting, over temperature, turn-on/off transient, subsonic filter, external mains fuse. [. . . ]