User manual LOWRANCE X-45

[. . . ] X-45 INSTALLATION AND OPERATION INSTRUCTIONS 1 TABLE OF CONTENTS INTRODUCTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 INSTALLATION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 INSTALLATION - Bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] The bottom signal and the digital depth display are read from the center element only. To turn the TargetTrack feature off, simply press the MENU key until its menu appears as shown below, then press the down arrow key. 14 CHART SPEED The rate echoes scroll across the screen is called the chart speed. It's adjustable by pressing the menu key until the chart speed menu appears. Echoes scrolling onto the screen will also show the effects of the change. To stop the chart, first clear any menu from the screen by pressing the ON/ CLEAR key. The chart will freeze and the word "STOP" appears at the top right portion of the screen. To start the chart, press the up arrow key again. DISPLAY MODE The X-45 has three different screen modes. To change modes, press the MENU key until the "DISP MODE" (Display Mode) menu appears. Then press the up or down arrow keys until the desired mode number appears. The modes are as follows: CHT 1 (Chart #1) This is the default mode used when the X-45 is first turned on. Digital Depth Display On 15 CHT 2 (Chart #2) Same as Chart #1 plus digital surface water temperature display. CHT 3 (Chart #3) Same as Chart #1 plus a digital speed display. CHT 4 (Chart #4) This is the High Speed Scroll mode. All Digital Displays Off 16 DIG 1 (Digital #1) This is the first digital only screen. It shows the digital depth display at the top of the screen in very large numbers. The shallow and deep alarm settings are displayed beneath the digital depth. No chart shows on this screen. DIG 2 (Digital #2) The digital depth display shows at the top of this screen in very large digits. When the X-45 is turned off, the log is reset to zero. ALARMS FISH ALARM The Fish Alarm sounds a tone when a fish symbol appears on the screen. To use the fish alarm, press the menu key until the "FISH ALARM" menu appears on the screen. (Note: If the Fish ID feature is off, it will be turned on when you turn the fish alarm on. ) DEPTH ALARMS The depth alarms are triggered only by the bottom signal. The shallow alarm sounds an alarm tone when the bottom goes 17 shallower than the alarm's setting. The deep alarm sounds a tone when the bottom goes deeper than it's setting. Shallow Alarm To set the shallow alarm, press the menu key repeatedly until the "SHAL ALARM" menu appears. Press the down arrow key to increase the shallow alarm's depth setting, the up arrow key decreases it. [. . . ] WARRANTY REPAIR WILL BE HONORED ONLY IN THE COUNTRY UNIT WAS PURCHASED. Please follow the shipping instructions shown below on this page if you have to mail your unit to the dealer. For proper testing, repair, and service, send a brief note with the product describing the problem. Be sure to include your name, return shipping address, and a daytime telephone number. Shipping Information When sending a product for repair, please do the following: 1. [. . . ]