User manual LOWRANCE X-1550 PAPER GRAPH

DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!

If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Diplodocs provides you a fast and easy access to the user manual LOWRANCE X-1550 PAPER GRAPH. We hope that this LOWRANCE X-1550 PAPER GRAPH user guide will be useful to you.


LOWRANCE X-1550 PAPER GRAPH : Download the complete user guide (368 Ko)

Manual abstract: user guide LOWRANCE X-1550 PAPER GRAPH

Detailed instructions for use are in the User's Guide.

[. . . ] INSTALLATION AND OPERATION MANUAL MODEL X-1550 GRAPH RECORDER · LOWRANCE ELECTRONICS, INC. 74128 PDF compression, OCR, web-optimization with CVISION's PdfCompressor High Speed (46 MPH. ) SUPPRESSION: OFF SENSITIVITY: ON 1/2 POSITION (1 NOTE POOR RECORD CAUSED BY NOT USING SUPPRESSION WHEN AT HIGH SPEED. Figure 44 . . . - --r Il-i SUPPRESSION: ON -- ADEQUATE SETTING SENSITIVITY: ON -- 1/2 POSITION High Speed (46 M. P. H. ) Figure 45 · !'· a · r -- iii:-. a. ¾ aaYr, -. . '1 Figure 46 SUPPRESSOR: MINIMUM RANGE: 0 TO 80 FEET PULSE WIDTH: 100 MICRO-SECONDS SENSITIVITY: 3/4 LINES: OFF PAPER SPEED: MAXIMUM 21 PDF compression, OCR, web-optimization with CVISION's PdfCompressor Electronics, Inc. , Customer Service Department in Tulsa, OK. Our Service Department may be able to save you the inconvenience of returning power. [. . . ] Do use the empty cardboard core from the last roll of paper on the take-up post. Do clean the stylus belt and wheels with alcohol after every five rolls of paper. Don't pull the platen assembly down when the stylus is at the front. Don't store any objectsinside the case or behind the viewing door. at battery; tighten power cord connector, Symptom On/Off switch is 'ON", have zero mark, but no echoes or bottom signals. What To Do Be sure the transducer is plugged into the unit and the transducer is in contact with the water. Symptom The unit is ON, but paper does not move. What To Do Tape Paper to cardboard spool on take-uppost. sitivity knob should be set at about ¾ point. Refer to the illustration below to see what effectthe Sensitivity setting has on the recorded information. Recording individual fish with an "arched" signature can usually be accomplished at trolling speed with the Sensitivity knob at the 3/4 point, or higher. Referto the section "Arched Signatures, " on page 10 for more information about this important function of your recorder. It can be caused by an electrical source, (such as the engine's ignition system), or by air bubbles in disturbed water which is called caviFigure 6 tation noise. In both cases, the noise could produce unwanted When high Sensitivity settings marks on the paper. (See Figure are used, a second bottom echo 44 & 45. ) Fortunately, noise pulses will appear. This is normal and is caused by the returning signal re- are relatively short in time comflectingoff the surface of the wapared to real sonar signals. Adter, making a second trip to the vancingthe Suppression knobwill cause the system to reject these bottom and back. about unwanted, short pulses without When detailed information brush piles, individual fish or the reducing the sensitivity in any way. This patented design is excluthermocline is desired, the Sen- Suppression Control The Suppression Control is Symptom Recorder marks are faint or dim. What To Do Clean viewing door; replace the stylus; check battery connections. Sympton Recorded marks are very heavy; paper is torn by stylus. What To Do Bend the stylus slightly to reduce pressure on paper. Don't forget to tape the paper to the take-up core. TROUBLESHOOTING Symptom On/Off switch is ON", but the stylus and paper don't move. What To Do Check fuse; check connections VI ADVANCED OPERATION Surface Clarity Control (SCC) The surface markings at the top of the chart paper can, at times, extend many feet below the surface. Surface clutter is caused by algae and plankton, air bubbles created by wave action or boat wakes, bait fish, or temperature inversions. The surface clutter can be reduced or eliminated by using the MARK/SCCkey on the control panel. To use the SCC, control, press 1 for minimum effect, 2 for an intermediate control, or 3 for maximum elimination of surface clutter, and then press MARK/SCC. [. . . ] Example: Press: SCALE Result: Figure 20 movement and counterclockwise for downward movement. Adjust until the top and bottom lines are the same distance from the edge of the paper. Caution: Do not force or jam screwdriver into the potentiometer slot as this could cause damage to your unit. Figure 22 Figure 30 PDF compression, 12 OCR, web-optimization with CVISION's PdfCompressor U IV HOW TO READ GRAPHS "Arched Signatures" X-1550 is that it can record individual fish with a characteristic arched mark that separates them from their stationary surroundings. [. . . ]

DISCLAIMER TO DOWNLOAD THE USER GUIDE LOWRANCE X-1550 PAPER GRAPH




Click on "Download the user Manual" at the end of this Contract if you accept its terms, the downloading of the manual LOWRANCE X-1550 PAPER GRAPH will begin.

 

Copyright © 2015 - manualRetreiver - All Rights Reserved.
Designated trademarks and brands are the property of their respective owners.