User manual LOWRANCE LMS-480M ADDENDUM

[. . . ] 988-0151-182 Addendum I LMS-480M, LMS-480DF & GlobalMap® 4800M This addendum addresses new items packed with your unit, changes to installation procedures, and NMEA 2000 ® upgrades not documented in the LMS 480M, LMS-480cDF and GlobalMap 4800M manuals. Your unit now packs with a 2-foot (61 cm) blue-to-red adapter cable, 15foot (4. 6 m) extension cable, LGC-3000 GPS module, double T connector and two 120-ohm terminators. The segment covering changes in installation procedures provides new backcase diagrams and information on how to add your unit to a new NMEA 2000 standard DeviceNet network. The upgrades covered in this document include information on the new LGC-3000 and instructions on how to configure and calibrate NMEA 2000 devices through the NMEA 2000 menu. [. . . ] Highlight BUS SETUP and press ENT, which will open the Bus Configuration menu. The following list of Temp Types will appear: Water, Outside, Inside, Engine Room, Cabin, Live Well, Bait Well, Refigeration, Heating System and Unknown. The following confirmation message will appear: Are you sure you wish to change this device's configuration?Advanced Options menu The Temp sensor Advanced Options menu contains two categories: Instance and Restore Defaults. 18 Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. Instance allows network technicians to resolve certain electronic probe conflicts. This is most likely to occur if the network includes LMF-200 or LMF-400 digital gauges, which support the display of fewer electronic probes than your GPS or sonar/GPS unit. If you want to use your unit in a network including one of these digital gauges, you may need to consult customer service. You should never need this command if you are connecting your unit to a network with similar display units and/or a series of electronic probes. Restore Defaults The Restore Defaults command allows you to reset an individual EP-35 Temp Sensor's settings to factory defaults. If, for example, you execute the Restore Defaults command from your Water Temp's Advanced Options menu, only the settings for the Water Temp will be reset to factory defaults. Other temps on the network will not be affected. To restore default settings: 1. The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization. Highlight BUS SETUP and press ENT, which will open the Bus Configuration menu. The following message will appear: Are you sure you wish to change this device's configuration?The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization. Highlight BUS SETUP and press ENT, which will open the Bus Configuration menu. The Device Configuration menu will appear with the Device Name dialog box highlighted. Press EXIT repeatedly to get back to the main display. To select a Location: 1. The NMEA 2000 menu will appear with five options: Bus Setup, Fuel Management, NMEA 2000 Alarms, Waypoint Sharing and Backlight Synchronization. Highlight BUS SETUP and press ENT, which will open the Bus Configuration menu. Select LOCATION and press ENT, which will open the Location menu with following options: Port, Center, Starboard and Unknown. The following message will appear: Are you sure you wish to change this device's configuration?Advanced Options menu The Fuel Flow sensor Advanced Options menu contains two categories: Instance and Restore Defaults. Instance The Instance command is intended for use only by experienced NMEA 2000 network technicians. [. . . ] If the amount of fuel you added to the tank and the fuel used figure are off by more than 3 percent, we recommend the engine interface be calibrated. NOTE: You must use the gauge's Fill Tank command when filling your fuel tank to keep the engine interface updated with correct information on the amount of fuel in the tank. To calibrate a Suzuki Engine Interface: 10. If calibration is necessary, press MENU|MENU, select NMEA 2000 and press ENT. Select TANK LOCATION and press ENT to choose the location of the tank connected to the selected engine interface. [. . . ]