User manual LOWRANCE GLOBALMAP 3300C

[. . . ] 988-0156-021 www. lowrance. com GlobalMap 3300C Mapping GPS Receiver Installation and Operation Instructions Copyright © 2004 Lowrance Electronics, Inc. Navionics is a registered trademark of Navionics, Inc. Points of Interest Data in this unit are by infoUSA, copyright 2001-2004, All Rights Reserved. infoUSA is a trademark of infoUSA, Inc. eXitSource Database, copyright 2001-2004 Zenrin Co. Ltd. Lowrance Electronics may find it necessary to change or end our policies, regulations and special offers at any time. [. . . ] The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001. " The waypoint symbol and number appear on the map. Create Waypoint by Entering a Position 1. Enter the latitude by pressing or to change the first character, then press to the next character and repeat until the latitude is correct. Enter the longitude by pressing or to change the first character, then press to the next character and repeat until the longitude is correct. The waypoint is saved and automatically given a name with a sequential number, such as "waypoint 001. " The waypoint symbol and number appear on the map and in the waypoint list. Navigate To a Waypoint You can select any waypoint visible on the Map Page with the cursor, then use the Navigate to Cursor command (we'll describe how later in this section. ) However, you can avoid scrolling the map to pick your waypoint if you use the Find Waypoint commands: 1. To look up the nearest waypoint, press to NEAREST|ENT; or, to look by name (and scroll through the entire waypoint list), press ENT. If your waypoint list is a long one, you can spell out the waypoint name in the FIND BY NAME box to search for it. (Press or to change the first character, then press to move the cursor to the next character and repeat until the name is correct, then press ENT to jump to the list below. ) 3. If the list is short, you can jump directly to the FIND IN LIST box by pressing ENT. Use or to select the waypoint name, press ENT and the waypoint information screen appears with the GO TO command selected. To begin navigating to the waypoint, press ENT. Waypoint Course line (red) Trail line (magenta) Off course range, set at 0. 15 mile Destination name Navigation Page, navigating toward waypoint 001 and leaving a trail. 47 Set Man Overboard (MOB) Waypoint One of boating's most terrifying events is having a friend or family member fall overboard. It's particularly dangerous at night or if you're out of sight of land. Of course, the first thing to do is remain calm and then use all standard safety procedures to rescue the person. This unit has a man overboard feature that shows navigation data to the location where the feature was activated. Your position at the time these keys are pressed is used as the man overboard position. Caution: Saving a new "Man Overboard" waypoint will overwrite and erase the previous "Man Overboard" waypoint. Navigate Back to MOB Waypoint Find your way back to the accident position with the Navigation Page or Map Page. When MOB is activated, the Navigation Page automatically shows the compass rose with its bearing arrow pointing toward the man overboard position, and the destination name says "Going To Man Overboard. " The Map Page displays a Man Overboard waypoint, represented by a human figure, and the steering arrow points where to steer to reach that position. Navigating to Man Overboard: "Man Overboard activated" message shown at left. The Navigation Page is shown in the center and Map Page is shown at right. The victim is astern of the vessel; the GPS shows which direction to steer to for the rescue. 48 The man overboard position is also stored in the waypoint list for future reference. This prevents the inadvertent loss of the current Man Overboard position. To cancel navigation to MOB, press MENU|MENU| to CANCEL NAVIGAto YES|ENT. The unit stops showing navigation information. TION|ENT| Navigate to Cursor Position on Map The GO TO CURSOR command: navigates to the current cursor position on the map. It's a quick and handy way to navigate to anything you can see on the map display. [. . . ] If you're in the United States and you have technical, return or repair questions, please contact the Factory Customer Service Department. Before any product can be returned, you must call customer service to determine if a return is necessary. Many times, customer service can resolve your problem over the phone without sending your product to the factory. To call us, use the following toll-free number: 800-324-1356 8 a. m. [. . . ]