User manual LOWRANCE EP-65R FLUID LEVEL QUICK GUIDE

[. . . ] 988-0154-372 EP-65R Fluid Level Electronic Sensor Installation, Configuration and Calibration Instructions This document shows how to install an EP-65R Fluid Level sensor and how to connect it to a NMEA 2000® network. It also provides instructions on how to configure and calibrate your fluid level sensor with Lowrance digital gauges (LMF-200 & LMF-400) and display units. NMEA 2000 is the communication bus standard developed by the National Marine Electronics Association (NMEA) for use in boats. Lowrance has introduced the LowranceNetTM, a line of products that can communicate over a NMEA 2000 network. [. . . ] When you attempt to reconfigure a fluid level to a configuration name already in use, the following message will appear: Name already in use. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 2. Highlight BUS DEVICES and press ENTER to bring up the Bus Devices list. The Fluid Level menu will appear with the following options: Fuel, Fresh Water, Waste Water (Gray Water), Live Well, Oil and Black Water. Select FUEL and press ENTER, which will open the Select Tank menu with up to three options. NOTE: If your gauge is set to a single-tank configuration you will be taken directly to the Bus Devices list where the tank will be displayed as Fuel Tank. You will be taken back to the Bus Devices list, where the tank will be displayed as Fuel Tank (P), Fuel Tank (C) or Fuel Tank (S). Press EXIT repeatedly to return to the main display. To reconfigure a fluid level for Oil: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. 2. Highlight BUS DEVICES and press ENTER to bring up the Bus Devices list. The Fluid Level menu will appear with the following options: Fuel, Fresh Water, Waste Water (Gray Water), Live Well, Oil and Black Water. Select OIL and press ENTER, which will open the Select Tank menu with up to three options. NOTE: If your gauge is set to a single-tank configuration you will be taken directly to the Bus Devices list where the tank will be displayed as Fuel Tank. You will be taken back to the Bus Devices list, where the tank will be displayed as Oil Tank (P), Oil Tank (C) or Oil Tank (S). 28 To reconfigure a fluid level for Fresh Water, Waste Water (Gray Water), Live Well or Black Water: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. The Fluid Level menu will appear with the following options: Level Warning, Unconfigure, Reconfigure, Calibrate, Reset Cal and Reset Values. The Fluid Level menu will appear with the following options: Fuel, Fresh Water, Waste Water (Gray Water), Live Well, Oil and Black Water. Select Fresh Water, Waste Water (Gray Water), Live Well or Black Water and press ENTER. Use the UP and DOWN keys to input the tank number you want to assign the fluid level and press ENTER. Use the UP and DOWN keys to input the size of the tank and press ENTER. You will be taken back to the Bus Devices list, where the fluid level will be displayed with its new configuration. NOTE: If your fluid level is not updated on the Bus Devices list, refresh the list by closing it, and then access it again. EP-65R Fluid Level Calibration The factory calibration settings for the EP-65R Fluid Level should be adequate for the majority of applications, so calibration will not be necessary in most cases. [. . . ] WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any non-conformity with the product's written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. [. . . ]