User manual LOWRANCE EP-60R FUEL FLOW QUICK GUIDE

[. . . ] 988-0154-432 EP-60R Fuel Flow Electronic Sensor Installation, Configuration and Calibration Instructions This document shows how to install an EP-60R Fuel Flow sensor and how to connect it to a NMEA 2000® network. It also provides instructions on how to configure and calibrate your fuel flow sensor with Lowrance digital gauges (LMF-200 & LMF-400) and display units. NMEA 2000 is the communication bus standard developed by the National Marine Electronics Association (NMEA) for use in boats. Lowrance has introduced a line of products that can communicate over a NMEA 2000 network (LowranceNet). [. . . ] If all three fuel flows are configured, which means there is no configuration name available, follow the first set of instructions. If the desired configuration name is available, follow the second set of instructions. Change Engine (active only with multiple-engine setting) The steps below show how to switch the configuration name of a fuel flow from Port engine to Starboard engine. If all fuel flows configured (Configuration name unavailable): 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. The following message will appear: Press Enter to UnConfig Device Name. You will be taken back to the Bus Devices list, where the Port fuel flow will now be displayed as UnCfg FFlow. The following message will appear: Press Enter to Configure Fuel Flow Sns. You will be taken back to the Bus Devices list where both fuel flows will be shown with their new configuration names. If desired configuration name available: 1. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. You will be taken back to the Bus Devices list, where the fuel flow you reconfigured will be displayed with its new configuration name. 24 EP-60R Fuel Flow Calibration The factory calibration settings for the EP-60R Fuel Flow should be within 3 percent, so calibration will not be necessary in most cases. NOTE: The Fuel Remaining Source must be set to fuel flow for the unit to correctly display fuel level information. Follow the instructions below to ensure fuel flow (Eng/FFlow) has been selected as the Fuel Remaining Source. Fuel Flow Accuracy To check fuel flow accuracy, add the Fuel Manager page to the page screen rotation and then customize it with Fuel Used data. To add the Fuel Manager page to the display: 1. A menu will pop up with four options: Add Page, Remove Page, Page Scrolling and Pop-Ups Setup. 2. Press ENTER, which will take you back to the main display, where the page you chose will be shown on the screen. To customize the Fuel Manager page: 1. With the Fuel Manager page on the display, Press MENU, select CUSTOMIZE and press ENTER. The data menu will appear with three options: Top Data, Center Data and Bottom Data -- each representing one of the three data boxes on the Fuel Manager page. If your unit is configured for more than one tank the Select Tank menu will appear. NOTE: If your unit is configured for a single-tank, the Select Tank menu will not appear. Press EXIT repeatedly to return to the main display where Fuel Used data will be displayed on the Fuel Manager page. Press EXIT twice to return to the main display where Fuel Used data will be displayed on the Fuel Manager page. To check fuel flow accuracy: 1. Make sure the Fuel Remaining Source has been set to Fuel Flow then fill up the tank connected to the fuel flow you want to calibrate. Press MENU, use the UP and DOWN keys to select SYSTEM SETUP and press ENTER. [. . . ] WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any non-conformity with the product's written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. [. . . ]