User manual LOWRANCE EP-50 STORAGE DEVICE

[. . . ] You should read all of the installation instructions before proceeding. You should decide where to install all components before drilling any holes in your vessel. You can download these free and get additional information on the NMEA 2000 compatible LowranceNET system at our web site, www. lowrance. com. All Lowrance NMEA 2000 capable devices are either NMEA 2000 certified or certification is pending. [. . . ] If you pick up a phone in your living room, you can hear someone talking into the phone in the bedroom. Network Nodes A network bus is built of network nodes spread along a backbone. Network nodes are made by fitting T-shaped connectors into the backbone (using the sockets on the sides), and attaching a display unit or sensor at the bottom of the "T. " Using our telephone example, the T connectors are similar to telephone jacks. Phones in a house must be connected to each other to communicate, and in the same way only sensors and display units plugged into the NMEA network can share information. Connections found in the middle of the bus will have one or more of these T-shaped connectors with the backbone cables plugged into both sides. Connections at the end of a network will have the backbone plugged into one side and a terminator plugged into the other, as shown in the following figure. Cable from sensor or display unit T connector LEI or Lowrance device needs an open T. Terminator at the very end of the bus Backbone cable (to rest of bus) NMEA 2000 network node located at the end of a NMEA 2000 bus. Adding a Network Node You can add a node anywhere along the network backbone where a connection already exists. This connection could be at the end of the network (between a T connector and a terminator), between two T connectors, between a T connector and a backbone extension cable, or between two extension cables. Wherever you want to add the new node, simply separate the sockets of the old connection and attach your new T connector between them. 3 Lowrance or LEI device connects to new T connector. Existing network node Add T-shaped connector to add device to bus. Attach terminator at end of bus. Add a new device to a NMEA 2000 bus by attaching a T connector between two T connectors, between a T connector and the end terminator, or between two backbone extension cables. If you want to add a node at the end of the line (as shown in the previous figure), remove the terminator from the very last connector, securely attach the new T connector, and then attach the terminator on the new connector. Additional Network Information Further instructions on creating or expanding a network are included in the NMEA 2000 network setup booklet, part number 988-0154-172, which came packed with this instruction sheet. 4 Notes 5 Notes 6 LOWRANCE ELECTRONICS FULL ONE-YEAR WARRANTY "We, " "our, " or "us" refers to LOWRANCE ELECTRONICS, INC. , the manufacturer of this product. "You" or "your" refers to the first person who purchases this product as a consumer item for personal, family or household use. We warrant this product against defects or malfunctions in materials and workmanship, and against failure to conform to this product's written specifications, all for one (1) year from the date of original purchase by you. WE MAKE NO OTHER EXPRESS WARRANTY OR REPRESENTATION OF ANY KIND WHATSOEVER CONCERNING THIS PRODUCT. Your remedies under this warranty will be available so long as you can show in a reasonable manner that any defect or malfunction in materials or workmanship, or any non-conformity with the product's written specifications, occurred within one year from the date of your original purchase, which must be substantiated by a dated sales receipt or sales slip. Any such defect, malfunction, or non-conformity which occurs within one year from your original purchase date will either be repaired without charge or be replaced with a new product identical or reasonably equivalent to this product, at our option, within a reasonable time after our receipt of the product. If such defect, malfunction, or non-conformity remains after a reasonable number of attempts to repair by us, you may elect to obtain without charge a replacement of the product or a refund for the product. THIS REPAIR, OR REPLACEMENT OR REFUND (AS JUST DESCRIBED) IS THE EXCLUSIVE REMEDY AVAILABLE TO YOU AGAINST US FOR ANY DEFECT, MALFUNCTION, OR NON-CONFORMITY CONCERNING THE PRODUCT OR FOR ANY LOSS OR DAMAGE RESULTING FROM ANY OTHER CAUSE WHATSOEVER. WE WILL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO ANYONE FOR ANY SPECIAL, CONSEQUENTIAL, INCIDENTAL, OR OTHER INDIRECT DAMAGE OF ANY KIND. Some states do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. [. . . ] To locate a Lowrance dealer, visit the web site, www. lowrance. com, and look for the Dealer Locator. To locate an Eagle dealer, visit the web site, www. eaglesonar. com, and look for the Dealer Locator. customers: LEI Extras Inc. , PO Box 129, Catoosa, OK 74015-0129 Call toll free in the U. S. , 800-324-0045, 8 a. m. Call toll free in Canada, 800-661-3983, or dial 905 629-1614 (not toll free), 8 a. m. [. . . ]