User manual LOGITECH HARMONY 895

[. . . ] 895 Harmony Remote User Manual version1. 0 User Manual Harmony 895 Table of Contents INTRODUCTION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 GETTING TO KNOW YOUR HARMONY REMOTE. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 BEGINNING THE SETUP PROCESS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 USING YOUR HARMONY REMOTE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Set Up Activities: Helps you provide us with information about the way your devices work together to perform Activities (e. g. Note: When using the Harmony remote software, click Help to view specific help for the step you are at. v. 1. 0 page 3 User Manual Harmony 895 Using Your Harmony Remote This section provides you with information that will help you use your remote. Using the Remote with the RF Wireless Extender The Harmony RF Wireless Extender allows you to use the Harmony remote to control devices that are out of view (e. g. Note: Update the RF Wireless Extender each time you make any changes to the configuration of your remote. The RF Wireless Extender has four dual-head IR (infrared) emitters (one emitter can control two devices) that can be used to control up to eight devices that are out of extender's range. Installing the RF Wireless Extender The extender can be wall-mounted or installed inside the cabinet where you devices are located. 1. 0 page 4 User Manual Harmony 895 Cabinet Adding the RF Wireless Extender to the Z-Wave Network Anytime you update the remote, you must add the RF Wireless Extender to your Z-Wave network again. Press Add on the remote when you see a message reminding you to add an RF Wireless Extender to your network. Anytime you update the RF Wireless Extender you must add the extender to your Z-Wave network again. Press the display button next to System Options on the remote's display. Press Connect on the RF Wireless Extender and follow the instructions on the remote. Using the Glow Button Press the Glow button to light up or turn off the display backlight. Click Settings. Recharging the Battery Place your remote in the base station to charge. 1. 0 page 5 User Manual · Harmony 895 The display and its backlight, and the keypad backlight remain on. Note: Press the GLOW button to turn the backlight off. · The battery level icon in the status bar flashes when the battery is still charging or will display a full battery level when charging is complete. When the battery is low, the display will flash a message to remind you to charge the battery. Using the Tilt Sensor Note: Whenever you pick up the remote from the base station, or replace it in the station, you will hear a beep. When you pick up the remote slightly tilted, the display will automatically turn on and the keypad light up. Click Settings. Selecting an Activity View the Activities you have added by pressing the Activities button. Press the corresponding display button next to the Activity you want to start. Note: If your devices are no longer responding consistently to your Harmony remote, but were doing so before, you may need to recharge the battery. Answer the questions on the remote's display by selecting Yes or No. If you answer no to any question, the Harmony remote will resend the necessary command and ask you the same question again. When you are done, the Harmony remote will be "in sync" with your devices again. Types of Help Available You can customize the Help button on your Harmony remote to provide one of the following types of help: · · Smart help Asks questions about the devices that are on during a specific Activity. Select Full help if you find devices aren't being controlled the way you want them to and the help on the remote is not asking you questions about these devices. Click Settings. Using the Remote Assistant Extra help is available from your remote by turning on the Remote Assistant. [. . . ] Custom-labeled buttons are displayed on the Harmony remote's display from left to right, top to bottom. Add a custom-labeled button to send a command to more than one device at a time: 1. Select a command from the drop-down list in each of the required device columns next to the name of the button you want to set. Click More Custom Labels to add labels one at a time. Changing the Settings for your Harmony Remote From Home in the Harmony software, click Remote Preferences to change the remote's settings: · · · · · Turn on/off Help on the remote/Remote Assistant (for additional information, see Displaying Help on Your Harmony Remote. ) Set the backlight timing (for additional information, see Using the Tilt Sensor and Using the Glow Button. ) Set the time-display format. [. . . ]