User manual LINKSYS WRT54G3G

[. . . ] 2, 4 GHz Wireless-G 802. 11g Router for 3G/UMTS Broadband WIRELESS User Guide Model No. WRT54G3G (EM) Wireless-G Router for 3G/UMTS Broadband Copyright and Trademarks Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use This User Guide This User Guide has been designed to make understanding networking with the Wireless-G Router for 3G/UMTS Broadband easier than ever. Look for the following items when reading this User Guide: This checkmark means there is a note of interest and is something you should pay special attention to while using the Wireless-G Router for 3G/UMTS Broadband. This exclamation point means there is a caution or warning and is something that could damage your property or the Wireless-G Router for 3G/UMTS Broadband. [. . . ] Enter the address of the PC whose connection you wish to test and how many times you wish to test it. Figure 5-47: Administration Tab - Diagnostics Traceroute Test Traceroute Parameters. Enter the address of the PC whose connection you wish to test and click the Traceroute button. Figure 5-48: Ping Test Figure 5-49: Traceroute Test Chapter 6: Configuring the Wireless-G Router for 3G/UMTS Broadband The Administration Tab - Diagnostics 47 Wireless-G Router for 3G/UMTS Broadband The Administration Tab - Factory Defaults Factory Defaults Restore Factory Defaults. Click the Yes button to reset all configuration settings to their default values, and then click the Save Settings button. Any settings you have saved will be lost when the default settings are restored. Click the Cancel Changes button to cancel your change. Figure 5-50: Administration Tab - Factory Defaults The Administration Tab - Firmware Upgrade Upgrade Firmware To upgrade the Router's firmware, first download the firmware from the Linksys website. Do not upgrade your firmware unless you are experiencing problems with the Router. For more information about upgrading firmware, refer to "Appendix C: Upgrading Firmware". IMPORTANT: After you upgrade the Router's firmware, follow these instructions: 1. Click the Yes button to reset the Router to its factory default settings. Figure 5-51: Administration Tab - Firmware Upgrade The Administration Tab - Config Management This screen is used to back up or restore the Router's configuration file. Backup Configuration To back up the Router's configuration file, click the Backup button. Then follow the on-screen instructions. Router Configuration To restore the Router's configuration file, click the Browse button to locate the file, and follow the on-screen instructions. After you have selected the file, click the Restore button. Chapter 6: Configuring the Wireless-G Router for 3G/UMTS Broadband The Administration Tab - Factory Defaults Figure 5-52: Administration Tab - Config Management 48 Wireless-G Router for 3G/UMTS Broadband The Status Tab - 3G/UMTS The 3G/UMTS screen on the Status Tab displays the Router's current mobile network and HSDPA/3G/UMTS card status. Mobile Network Status Mobile Network Bearer. Displayed here is the name of the mobile network bearer the Router is using. Displayed here is the name of the HSDPA/3G/UMTS or GPRS network the Router is using. To select a different network, click the Select Network button and follow the on-screen instructions. This indicates the strength of the HSDPA/3G/UMTS or GPRS signal that the Router is receiving. This is the length of time the Router has been connected to the HSDPA/3G/UMTS or GPRS network since your last connection. Displayed here is the amount of data that has been sent to and received from the HSDPA/3G/UMTS or GPRS network since your last connection. Click the Refresh button to view the latest status information. Chapter 6: Configuring the Wireless-G Router for 3G/UMTS Broadband The Status Tab - 3G/UMTS 49 Wireless-G Router for 3G/UMTS Broadband The Status Tab - Router The Router screen on the Status Tab displays the Router's current status. Router Information Firmware Version. This is the specific name for the Router, which you set on the Setup Tab. [. . . ] Unless this 2, 4-GHz wireless LAN product is operating within the boundaries of the owner's property, its use requires a "general authorization". Questo prodotto è conforme alla specifiche di Interfaccia Radio Nazionali e rispetta il Piano Nazionale di ripartizione delle frequenze in Italia. Se non viene installato all'interno del proprio fondo, l'utilizzo di prodotti Wireless LAN a 2, 4 GHz richiede una "Autorizzazione Generale". Consultare http://www. comunicazioni. it/it/ per maggiori dettagli. Appendix I: Regulatory Information 89 Wireless-G Router for 3G/UMTS Broadband Latvia The outdoor usage of the 2, 4 GHz band requires an authorization from the Electronic Communications Office. [. . . ]