User manual LINKSYS WET610N

[. . . ] 15 Wireless Security Checklist Change the default wireless network name or SSID Change the default password Enable MAC address filtering Enable encryption Status > Bridge . 13 i Linksys WES610N/WET610N Product Overview Product Overview Thank you for choosing the Linksys Dual-Band N Entertainment Bridge. The bridge can connect any wired, Ethernet device to your wireless network. The bridge is based on dual-band Wireless-N, so it is compatible with any Wireless-N, -G, -A, or -B router or access point. [. . . ] Voice Use Aggregation  This option defines whether or not the Media Access Control (MAC) layer will set up an Add Block Acknowledgement (ADDBA) session. Accept Aggregation  This option defines whether or not the MAC layer will accept an ADDBA request. Number of Packets in Aggregation  This option defines the maximum number of packets (sub-frames) in the aggregate. Aggregation Size  This option defines the maximum size of the aggregate (in bytes). Timeout Internal  This option defines the timeout period in which the aggregate should be closed with a “closing condition” before it is closed by the timer. Size of Packet in Aggregation  This option defines the minimum size (in bytes) of packets to be accumulated in the aggregate. Note The settings on the Advanced Wireless Settings screen are designed for advanced users only. advanced Wireless Use LDPC  Low-Density Parity-Check Code (LDPC) enables or disables error correction to reduce the probability of data loss in noisy channels. The Rate Adaptation algorithm automatically disabled LDPC coding when working at high PHY rates (higher than 162). To use the LDCP advanced error correction scheme, keep the default, Yes. 11b rates, the bridge informs the wireless network that OFDM packets are going to be transferred and protects the packets in the wireless network. The RTS/CTS and CTS2Self packets create overhead, which may result in lower throughputs. The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. 11n Protection Type  This option configures protection from non-High Throughput (HT) devices within the wireless network. In case the wireless router (or access point) detects an association of a non-HT legacy device, it will signal all the HT devices to use RTS/CTS or CTS2Self mechanisms before each data transmission. The RTS/CTS option provides better coverage but lower throughputs when compared to CTS2Self, because the RTS/CTS option includes acknowledgement from the receiving device. Percentage of maximal transmit power  This option sets the percentage of maximal transmit power relative to the regulatory domain restrictions. For example, if the regulatory domain restriction allows transmissions of up to 20 dB, then setting the percentage at 50% allows maximal transmit power of 10 dB. 1Q mapping from the IP DSCP/TOS field to WMM priorities (Background, Best Effects, Video, Voice). Re-establish Ethernet connection when initiating wireless connection  To trigger DHCP discovery from the device that resides behind the bridge, the bridge will reset the Ethernet link between the bridge and the device every time a wireless connection is established. Click Save Settings to apply your changes, or click Cancel Changes to cancel your changes. Advanced Configuration Administration > Management Use this screen to manage specific bridge functions: access to the web‑based utility, backup of the configuration file, and reboot. [. . . ] Klikk på Save Settings (Lagre innstillinger) for å ta i bruk endringene, eller klikk på Cancel Changes (Forkast endringer) for å forkaste endringene. Upgrade Firmware (Oppgrader fastvare) Please select a file to upgrade the firmware (Velg en fil for å oppgradere fastvaren)  Klikk på Browse (Bla gjennom), og velg filen med fastvareoppgraderingen. Hvis du valgte Wide - 40MHz Channel (Bred - 40 MHz-kanal) som ruterinnstilling for radiobånd eller kanalbredde, vil standardkanalen være en sekundær kanal for Wireless-N. Security (Sikkerhet)  Sikkerhetsmetoden for det trådløse nettverket vises. [. . . ]