User manual LINKSYS PSUS4

[. . . ] ® A Division of Cisco Systems, Inc. PrintServer for USB with 4-Port Switch WIRED User Guide Model No. PSUS4 PrintServer for USB with 4-Port Switch Copyright and Trademarks Specifications are subject to change without notice. Other brands and product names are trademarks or registered trademarks of their respective holders. How to Use this User Guide This User Guide has been designed to make understanding networking with the PrintServer easier than ever. Look for the following items when reading this User Guide: This checkmark means there is a note of interest and is something you should pay special attention to while using the PrintServer. This exclamation point means there is a caution or warning and is something that could damage your property or the PrintServer. [. . . ] To start the Bi-Admin program, click on Start, Programs, Print Server Utility, and then Bi-Admin Management Utility, as shown in Figure 8-6. If the Bi-Admin Management Utility icon has been created, you can just double-click on it instead. You can drag the shortcut icon onto your Desktop for easy access to the Bi-Admin Management Utility. When the Bi-Admin Management Utility appears, it will ask for the Connected Protocol. Then the Bi-Admin Management Utility will automatically scan the network for the USB PrintServer. (See Figure 8-8. ) Figure 8-6: Connected Protocol Figure 8-7: Searching for Device Figure 8-8: Setup Complete Chapter 8: Bi-Admin Management Starting the Bi-Admin Management Utility 29 PrintServer for USB with 4-Port Switch The Bi-Admin Management Utility The Bi-Admin Management Utility screen will appear next. Any hardware found on the network will appear on the left-hand side of the screen, as shown in Figure 8-9. The menu and Icon options will be explained below: Menu Options Main. The options are Device Status, Printer Status, Configuration, Upgrade, Refresh, and Exit. These options are also the same as the Icons that are displayed below the menu options (viewed from left to right), and are described below. This option allows you to view all of the device settings, and optionally save the device settings to a file, or restore a previously saved file to the device. A list of the PrintServer's device settings is displayed that contains the Hardware ID, Firmware version, Protocol ID, Default Name, and Server Name. To choose a different device that you configured, click the Open button. The contents of the file will display on the right-hand side of the screen. Figure 8-9: Bi-Admin Management Utility Figure 8-10: Device Information Figure 8-11: Verify Password Chapter 8: Bi-Admin Management The Bi-Admin Management Utility 30 PrintServer for USB with 4-Port Switch · Printer Status. This option allows you to view the printer status, and set port and printer parameters. If you click this option, a Verify Password screen will appear, as shown in Figure 8-11. Make sure that you enter the password in the field before you click OK or an Incorrect Password message will appear. If the message appears, then click OK, enter the correct password in the field, and click OK again. After the password is successfully entered, the Printer Status screen will appear, as shown in Figure 8-12. The Device Name will be displayed and USB Printer Port will be highlighted. Click the Back button to return to the Bi-Admin Management Utility screen. [. . . ] WLAN (Wireless Local Area Network) - A group of computers and associated devices that communicate with each other wirelessly. Appendix E: Glossary 47 PrintServer for USB with 4-Port Switch Appendix F: Specifications Standards Ports/Buttons Cabling Type male connectors LEDs Dimensions (W x H x D) Unit Weight Power Certifications Operating Temp. Operating Humidity Storage Humidity IEEE 802. 3, 802. 3u, USB 1. 0/1. 1 4 10/100 RJ-45 Ports Auto MDI/MDI-X, Reset Category 5 or better, and USB1. 1 cable with Type-B female and Type-A Status, USB, 1-4 3. 66" x 1. 18" x 3. 54" (93 mm x 30 mm x 90 mm) 7. 8 oz. (0. 221 kg) External, 5V DC, 2. 5A FCC, CE Class B 0ºC to 40ºC (32ºF to 104ºF) -20ºC to 70ºC (-4ºF to 158ºF) 10% to 85% Non-Condensing 5% to 90% Non-Condensing Appendix F: Specifications 48 PrintServer for USB with 4-Port Switch Appendix G: Warranty Information LIMITED WARRANTY Linksys warrants to the original end user purchaser ("You") that, for a period of three years, (the "Warranty Period") Your Linksys product will be free of defects in materials and workmanship under normal use. Your exclusive remedy and Linksys's entire liability under this warranty will be for Linksys at its option to repair or replace the product or refund Your purchase price less any rebates. [. . . ]