User manual LINKSYS PCMPC200

[. . . ] Instant EtherFast® Series EtherFast® 10/100 CardBus PC Cards Use this guide to install these Linksys Products: Linksys EtherFast 10/100 CardBus PC Card (PCMPC200 v2) Linksys EtherFast 10/100 Integrated CardBus PC Card (PCM200 v2) User Guide COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All Rights Reserved. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors. LIMITED WARRANTY Linksys guarantees that every EtherFast 10/100 CardBus PC Card is free from physical defects in material and workmanship under normal use for one (1) year from the date of purchase. [. . . ] You should see an icon for the Entire Network, and/or the names of the other PCs on the network. In order to see your other computers in Network Neighborhood, you need to enable File and Printer Sharing. To enable File and Printer Sharing refer to page 37 of this User Guide. If you don't see anything at all, press the F5 key on your keyboard a few times to refresh the screen. If you only see your computer in Network Neighborhood, skip to Troubleshooting problem 6 on page 35. If you only see computers that are running the same operating system as you and you don't see any others, go to Troubleshooting problem 10 on page 36. If you see all computers on the network except yours, and the other PCs can't see your computer, see Troubleshooting problem 7 in on page 35. 13. Your system may or may not ask you for your Windows 95 CD-ROM or the location of the 95 installation files. Direct Windows to the appropriate location, (e. g. , "D:\win95", "C:\windows\options\cabs"). Once Windows is done copying the necessary files, the System Settings Change window appears. Remove all disks from your computer and click on Yes to restart your PC. If you don't see this window, simply close down Windows 95 and restart your computer by clicking on the Start button, then Shut Down, select Restart the Computer, then click Yes. If your cabling is properly attached and the network is detected, the green Link light will be on, and the Activity (ACT) light will be flickering or solid. 20 21 Linksys Instant EtherFast® Series EtherFast® 10/100 CardBus PC Cards Windows 2000 Installation and Setup Overview After physically installing the EtherFast 10/100 CardBus PC Card in your computer, follow these instructions to install the network driver. Note: Screen shots used in this Installation and Setup section are from installation of the standard EtherFast 10/100 CardBus PC Card (PCMPC200 v2). If you are installing the EtherFast 10/100 Integrated CardBus PC Card (PCM200 v2), the installation process will be unchanged, however, the product name will be different. 4. The Locate Driver Files dialog box will appear. Select the "Floppy disk drives" option, insert the Linksys EtherFast 10/100 CardBus PC Card Driver Disk into your floppy drive. The Completing the Found New Hardware Wizard dialog box will appear. Click Next. The Install Hardware Device Drivers dialog box will appear. The following adapter name will be shown: Linksys EtherFast 10/100 CardBus PC Card II Click Finish. When Ethernet Controller is displayed, select "Search for a suitable driver for your device (Recommended)". Click Next. 22 If you want to share files or printers, refer to the Windows 2000 documentation 23 Linksys Instant EtherFast® Series EtherFast® 10/100 CardBus PC Cards Windows NT 4. 0 Installation and Setup Overview The following instructions will set up an NT 4. 0 server/workstation on your PC. You should have your original Windows NT CD-ROM handy during the installation, as you might be asked to supply it. Note: Screen shots used in this Installation and Setup section are from installation of the standard EtherFast 10/100 CardBus PC Card (PCMPC200 v2). If you are installing the EtherFast 10/100 Integrated CardBus PC Card (PCM200 v2), the installation process will be unchanged, however, the product name will be different. 3. button to select a network adapter. To install the network driver for an NT 4. 0 Server or Workstation 1. Click on Start, Settings, Control Panel, and then double-click on the Network icon. [. . . ] Client for NetWare Networks If you plan on connecting to a Novell NetWare server, click on the Add button. In the Network Client window, select Manufacturer and choose Microsoft. Under the Network Protocol box, highlight IPX/SPX-compatible protocol. Click OK. Note: After manually installing a component, you will be asked to reboot your computer. [. . . ]