User manual LINKSYS PCM100

[. . . ] Instant EtherFast® Series EtherFast® 10/100 PC Cards Use this guide to install: EtherFast 10/100 PC Card (PCMPC100 v3) EtherFast 10/100 Integrated PC Card (PCM100 v2) User Guide COPYRIGHT & TRADEMARKS Copyright © 2001 Linksys, All Rights Reserved. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors. LIMITED WARRANTY Linksys guarantees that every EtherFast 10/100 PC Card is free from physical defects in material and workmanship under normal use for FIVE years from the date of purchase. [. . . ] Once Windows has located the driver, a message will appear that reads Windows is now ready to install the Linksys EtherFast 10/100 PC Card V3 driver. Click Next. Installing the PC Card's Driver Windows will begin copying the necessary files onto your computer. Windows will automatically detect the presence of the EtherFast 10/100 PC Card in your computer and display the Update Device Driver Wizard window. Insert the EtherFast 10/100 PC Card Driver Disk into your Notebook PC's floppy disk drive and click Next. If Windows asks you to supply the original Windows ME CD-ROM, insert it now and direct Windows to the proper location for the disk (e. g. , "c:\windows\options\Install" or "D:\Win9x"). If Windows asks you to supply a driver containing the letters "pc100", enter "a:\" in the Copy Files From box and click Enter. 22 23 Instant EtherFast® Series EtherFast® 10/100 PC Cards 6. When you are asked if you want to restart your computer, remove any Driver Disks from the floppy disk drive, click Yes, and allow your system to restart. Windows NT 4. 0 Installation and Setup Overview The following instructions will set up an NT 4. 0 server/workstation on your PC. You should have your original Windows NT CD-ROM handy during the installation, as you might be asked to supply it. Note: Screen shots used in this Installation and Setup section are from installation of the standard EtherFast 10/100 PC Card (PCMPC100 v3). If you are installing the EtherFast 10/100 Integrated PC Card (PCM100 v3), the installation process will be unchanged, however, the product name will be different. 7. After Windows restarts, enter a User Name and a Password when prompted, and click the OK button. Once you are back on the Windows desktop, you can make the necessary changes to your system's network settings by clicking on the Start button, then Settings, then Control Panel, then double-click the Network icon. Note: Linksys does not provide technical support for TCP/IP configuration or troubleshooting. To install the network driver for an NT 4. 0 Server or Workstation 1. Click on Start, Settings, Control Panel, and then double-click on the Network icon. If you have not previously installed Windows NT networking on your computer, a message will appear that reads: Windows NT Networking is not installed. Do you want to install it now? · If you see this message, click Yes to install NT networking along with the EtherFast Card's network driver, and continue with step 1 below. Confirm that all the following network components are installed: · Client for Microsoft Networks · Linksys EtherFast 10/100 PC Card (PCMPC100 V3) · TCP/IP To set up File and Printer Sharing, or to configure Client for Microsoft Networks or Client for Netware Networks, please refer to the Appendix. Your EtherFast card is now successfully set up. 24 · If you don't see this message, NT networking is already installed. Skip to the section entitled Installing the EtherFast Network Driver if Networking is Already Installed. Click Next. 25 Instant EtherFast® Series EtherFast® 10/100 PC Cards 3. Type "A:\" into the box on your screen and click the OK button. 7. Place check marks beside each listed network protocol that you wish to install. See your Microsoft Windows NT user guide or talk to your network administrator for more information about network protocols. When you're finished, click Next. Note: If you install the TCP/IP protocol, refer to your Windows NT documentation when installation steps that aren't listed in this User Guide appear. Linksys does not provide technical support for the configuration or troubleshooting of the TCP/IP protocol. 5. [. . . ] · Client for Microsoft Networks · Linksys EtherFast 10/100 PC Card (PCMPC100 v3) · TCP/IP There may be other components listed in addition to the ones shown above. Client for Microsoft Networks If you plan on connecting to an NT file server or peer-to-peer network, click on the Add button. If you install the TCP/IP protocol, refer to your Windows NT documentation when installation steps that aren't listed in this User Guide appear. Note: Linksys does not provide technical support for TCP/IP configuration or troubleshooting. 9. The Network Adapters category should be removed from the Device Manager listing. [. . . ]