User manual LINKSYS EFSP42

[. . . ] Instant EtherFast© Series EtherFast 10/100 PrintServers Use this User Guide to install the following Linksys products: · EtherFast 10/100 2-Port Switched PrintServer (EFSP42) · EtherFast 10/100 3-Port Print Server (EPSX3) · EtherFast 10/100 1-Port Print Server (PPSX1) User Guide COPYRIGHT & TRADEMARKS Copyright © 2000 Linksys, All Rights Reserved. Instant EtherFast 10/100 PrintServer is a registered trademark of Linksys. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors. [. . . ] Install the PrintServer again in NetWare 4. x NDS environment. Problem 10: Problem 6: Solution 6: I used the Capture command to print a job, but the job was separated into two parts. Increase the timeout value of the Capture command by using the option /TI=n of the Capture command to increase the time-out value, where n is the value of timeout. Solution 10: 50 51 Instant EtherFast® Series EtherFast 10/100 PrintServers Problem 11: Solution 11: The "String Before Job" and/or "String After Job" set tings in the Logical Printers don't work properly. If your PrintServer is configured as a NetWare Print Server and you want it to service more than one bindery file server, perform the following steps. Log in, with supervisory rights, to the other file servers you want your PrintServer to service. Create queues and a print server name for your PrintServer on each file server you want to service. Log in, with supervisory rights, to the master file server of your PrintServer. Select Print Server Information, then select your PrintServer in the print server list. Select Printer Server Configuration, then select File Server To Be Serviced. Insert the file server names of the other file servers to be serviced by your PrintServer. In NetWare Remote Printer mode, if you want each port of the PrintServer to attach to a different NetWare Print Server, perform the following steps. Use PCONSOLE to create and assign the required printers and queues as detailed in the Remote Printer Mode section. Enter the correct NetWare print server names in the print server name fields, then select Execute Setup. Windows Printing Issues Problem 1: When printing from some software applications such as Power Point, it takes a long time and the print-out is incorrect. The problem is due to the printer being configured to Start printing after the first page is spooled. When the Spool Settings Dialogue field appears, choose Start printing after last page is spooled and click OK. Problem 2: While adding my printer as instructed in Windows 95 or 98, I received a message stating that Printer could not be found. Some printer drivers, when configured as Local Printer, will poll the printer to see if it is connected. Select Network Printer when asked How is the printer attached to your computer?Then when prompted for Network Path or Queue name enter a dummy value such as \\SCnum\P1 or P2 or P3 for LPT2 or LPT3 respectively, and select Next 3. The printer wizard will display a message stating the Network Printer is off-line. The printer icon will be grayed out indicating the printer is not ready. Check the 53 Solution 1: Problem 12: Solution 12: Solution 2: Problem 13: Solution 13: 52 Instant EtherFast® Series EtherFast 10/100 PrintServers Work off-line option is OFF. If the printer is connected and powered On, the printer icon should no longer be grayed out, and you should be able to print. [. . . ] Standard print servers cannot work with bidirectional printers, but the EtherFast PrintServer features a custom design to support both parallel as well as bidirectional parallel interfaces. However, the EtherFast PrintServer cannot pass messages from the printer back to the printing PC -- this limitation is simply an industry standard, and not one of the PrintServer itself. However, the PrintServer can check any printer's online and printing status on the network with the Bi-Admin management utility software packaged with the PrintServer. The status-checking feature built into the management software does not require a bidirectional printer to function. [. . . ]