User manual LINKSYS EFG80

[. . . ] Instant GigaDriveTM Series EtherFast® Network Attached Storage with 80 GB Hard Drive + PrintServer Use this guide to install: EFG80 User Guide COPYRIGHT & TRADEMARKS Copyright © 2002 Linksys, All Rights Reserved. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation. All other trademarks and brand names are the property of their respective proprietors. LIMITED WARRANTY Linksys guarantees that every Instant EtherFastTM EtherFast® Instant GigaDriveTM will be free from physical defects in material and workmanship for twq years from the date of purchase, when used within the limits set forth in the Specification section of this User Guide. [. . . ] The web utility can be accessed by any PC on the network by typing http://192. 168. 1. 77 in the PC's web browser address window, as shown in Figure 5-1. Figure 5-1 After you press the Enter key, the Web Management Home Page will appear, shown in Figure 5-2. From this page, you can set a password, administer the Instant GigaDriveTM, view this user guide, and even go to the Linksys web site. If you click the links to User Log in, you will be required to enter your User Name and Password. (See the Administration section for information about entering this information. ) Figure 4-11 Figure 5-2 16 17 Instant GigaDriveTMSeries Etherfast Network Attached Storage User Password Tab Administration Tab - LAN When you click the Administration tab, a password request page will pop up, as shown in Figure 5-4. (Windows XP users will see a "Connect to" window. ) Enter the User Name and Password you use to access the Instant GigaDriveTM and click the OK button. To cancel the log in procedure, click the Cancel button. Figure 5-4 After logging in, you will see the Administration tab's LAN screen, shown in Figure 5-5. This is the default screen that appears whenever you log in to the Administration tab. Figure 5-3 From the User Password tab, any user can change their password for interacting with the Instant GigaDrive's web-based utility. Then, enter the password you use when accessing the Instant GigaDrive's web-based utility. Enter this new password again in the Confirm New Password field and click the Save button to save this new password. To Cancel this procedure and clear all the fields, click the Cancel button. For further information about anything on this screen, click the Help button. Figure 5-5 18 19 Instant GigaDriveTMSeries Etherfast Network Attached Storage From the LAN screen, you will be able to configure some of the settings you saw in the Setup Wizard. While these changes are being made, you can click the Save button to save these changes, Cancel to clear all changes, or Help to get further information about anything on this screen. IP Address These fields allow you to Obtain an IP Address Automatically or use a Fixed IP Address. Obtain an IP Address Automatically is the same as using the Dynamic IP Address setting in the Setup Wizard and should be used if you already have a DHCP server, setting IP Addresses on your network devices. Use this setting if there is no DHCP server on your network and you wish the Instant GigaDriveTM to use one, static IP Address. With the Fixed IP Address setting, you can also use the Instant GigaDriveTM as your network's DHCP server. When using the Fixed IP Address setting, you must enter the IP Address, Network Mask (the same as the Subnet Mask), and Default Gateway. The IP Address setting should contain an unused IP Address that contains the same LAN segment as the network on which the Instant GigaDrive is running. The Network Mask setting must match the other devices on your network. If you have a router on your network enter its IP Address in the Default Gateway field. DHCP Server The Instant GigaDriveTM can serve as your network's DHCP server if no other device is funtioning as a DHCP server on your network. [. . . ] · If you don't have a router, ensure that your IP Address is compatible with the Instant GigaDrive's. 255. 255. 255. 0) · If you do have a router, check that your Gateway IP Address is set correctly. When I click on the GigaDrive icon in Network Neighborhood, I'm prompted for a password. This can happen in the following situations: · Your Windows Logon name is recognized by the GigaDrive, but your Logon password is not. [. . . ]